HI friends
mine one of the friends have ask a good question i also
donot know the answer so i am putting here
Please poet the answer no matter it is wright or wrong put
yours view here
The question is like that
when we are going to configure ospf then there are three
way
1st way
router ospf 10
netwrok 192.168.1.0 0.0.0.255 area 0
network 192.168.2.0 0.0.0.255 area 0
the 2nd way is like that
router ospf 10
netwrok 192.168.0.0 0.0.255.255 area 0
but he inrodused the thrird way
like
router ospf 10
netwrok 192.168.00000001.0 < ?.?.?.?>area 0
router ospf 10
netwrok 192.168.00000010 <?.?.?.?>area 0
now problem is that what should i put the mask in this way
so i puted ? sign
Please solve this problem
i think this is good one
plz donot see for answer please contribute any thing
i am reqesting
Than you
Jitendera kuamr sinha
- 5 Answers
- 5088 Views
- I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / chijo mathew
mask for 192.168.00000001.0 is 0.0.1.255 and mask for
192.168.00000010.0 is 0.0.3.255
| Is This Answer Correct ? | 3 Yes | 0 No |
Hi Jitendera
Kapil on this side I will try to explain
See
Two method u know very well. 3rd is like that
Suppose we have route in router area 1 is
192.168.1.0
192.168.2.0
192.168.3.0
192.168.4.0
192.168.5.0
192.168.6.0
Now we convert 3rd bit in binary
128 64 32 16 8 4 2 1
192.168.00000001.0
192.168.00000010.0
192.168.00000011.0
192.168.00000110.0
192.168.00000101.0
192.168.00000110.0
Now make a mask.
192(8bit).168(8bit).5bit(see zero).0
Now the 1 to 6 route ip is 192.168.0.0
And mask is 255.255.248(5bit of binary).0
Now the wild make is 0.0.7.255
Now the route of ospf is
Network 192.168.0.0 0.0.7.255
sorry if any thing i forgot to tell....
| Is This Answer Correct ? | 2 Yes | 0 No |
Answer / jitenderasinha
Thanks Chijo Mathew
i was waiting for any answer and at first sight it is
looking correct i will try it this one on my lab routers
i will let you know the result.
Thanks again
Jitendera kuamr sinha
| Is This Answer Correct ? | 0 Yes | 0 No |
Answer / jitendera
Hi Chijo Mathew
i have trid this one what u have suggestd but i am getiing
errro like ""unkonown command""
i am using 2621 cisco router
is this router is going to support the this commnad ?
| Is This Answer Correct ? | 0 Yes | 0 No |
Answer / jitendera
Hi kapil
i have alraedy tried this one on mie physiacl router setup
but while implemnting this command it is giving the error
what i have mentioned above
| Is This Answer Correct ? | 0 Yes | 0 No |
Which command-line keywords are valid for choosing Frame-Relay LMI types? A.) itu-t B.) dlci C.) ansi D.) rfc 1544 E.) cisco F.) q933a
Default packet size of ipv6?
Tell me CCNA Course + Dump Q/A in chennai?
What command would you use to find out the names of Novell servers on a network? A. show ipx servers B. show ipx hosts C. show ipx sap D. show ipx nodes.
Can you explain encapsulating, carrier and passenger protocol?
In eigrp metric parameters which 2 options are enable by default?
Dear Mr.Shahin thank you very much for your advise i realy thanks full to you. Best of luck
If you are running Token Ring with Novell IPX routing, which encapsulation should you use? A.) SAP B.) SNAP C.) 802.5 D.) 802.2
Which command loads a new version of the Cisco IOS into a router? A. copy flash ftp B. copy ftp flash C. copy flash tftp D. copy tftp flash
The -- terminal no editing -- command will perform what function? A.) Edit the contents of NVRAM B.) Allows access to the terminal port C.) Stops the advanced editing feature D.) Enable password functions
HOW MPLS IS DIFFERENT FROM OSPF? WHY NOW A DAYS MPLS IS PREFERED OVER ANY NETWORK PROTOCOL?
Identify the access-list range for an extended IP access-list? A.) 800 - 899 B.) 1 - 99 C.) 1000 - 1099 D.) 100 - 199
CCNA 
