Answer / guest

Answer: D

hi i am facing one problem.ptoblem is like that i am getting output error on mine router ethernet interfae here is the cisco#show interface e0 Ethernet0 is up, line protocol is up Hardware is QUICC Ethernet, address is 0030.802d.2a17 (bia 0030.802d.2a17) Internet address is 202.122.20.225/28 MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec) ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:00, output 00:00:00, output hang never Last clearing of "show interface" counters 05:55:07 Queueing strategy: fifo Output queue 0/40, 0 drops; input queue 0/75, 0 drops 5 minute input rate 10000 bits/sec, 11 packets/sec 5 minute output rate 29000 bits/sec, 11 packets/sec 1515202 packets input, 359100396 bytes, 1 no buffer Received 6 broadcasts, 0 runts, 0 giants, 1 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 0 input packets with dribble condition detected 1584394 packets output, 1623395338 bytes, 0 underruns 1820 output errors, 26732 collisions, 0 interface resets 0 babbles, 0 late collision, 9698 deferred 18 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out output cisco# what is the reason how to solve this please tell me i am using cisco asa 5520 behid mine internet router and no error on the asa inside interface

2 Answers  

---

what is the basic rules for ACLs?

4 Answers  

---

I have layer 3 Cisco 3560(Multilayer) switch right.How we can configure sub interface & Inter VLAN(we have vlan 2,3 & 10 ),Each VLan talk with each other?

4 Answers   IBM,

---

Which three statements about common elements of the TCP/IP protocol stack are true? (Choose three) A. IP provides connectionless service and routing capabilities B. APP enables devices to locate the IP address of local devices C. UDP provides simple connectionless service without windowing or acknowledgments D. ICMP provides connection oriented management data to routers and Layer 3 switches E. TCP enables devices to send large quantities of data using windowing in a connection oriented manner

2 Answers  

---

Hi- Salmaan my name is Shadab Khan and nick Khangkp ok salmaam plz tell me about of NAT plz

3 Answers  

---

As the system administrator, you enter the following commands at the command prompt: ipx routing access-list 800 permit 2b 4d int e0 ipx network 4d ipx access-group 800 out int e1 ipx network 2b int e2 ipx network 3c What did these command accomplish? A. Traffic from network 4c destined for network 4d will be forwarded out Ethernet0. B. Traffic from network 3c destined for network 4d will be forwarded out Ethernet0. C. Traffic from network 2b destined for network 4d will be forwarded out Ethernet0. D. Traffic from network 4d destined for network 2d will be forwarded out Ethernet0.

1 Answers  

---

Identify the command mode necessary to enter the standard ping command? A.) Router(config)# B.) Router> C.) Router(std-ping)# D.) Router(config-if)#

1 Answers  

---

You want a message to be displayed every time someone tries to log on to the router. Which command is required to accomplish this task? A.) motd#(message)# B.) banner motd(message) C.) banner motd#(message)# D.) banner motd*(message) E.) banner login#(message)#

1 Answers  

---

Based on the DR AND BDR discussion i want to put one question the question is what is the name of protocol which is responsible;e for DR and BDR selection

7 Answers   Patni,

---

What is Transport and Tunnel mode?

0 Answers   CCIE,

---

Does a bridge divide a network into smaller segments?

0 Answers  

---

Write an access list line which will deny node 20.0.2.1 to anywhere on your network using DNS via UDP. Don't worry about the other access list lines.

2 Answers  

---