You need to come up with a TCP/IP addressing scheme for your company. Which two factors must you consider when you define the subnet mask for the network? A.) The location of DHCP servers B.) The volume of traffic on each subnet C.) The number of subnets on the network D.) The location of the default gateway E.) The number of host IDs on each subnet

2 Answers  

---

What is the default IPX Ethernet encapsulation? A.) SNAP B.) Arpa C.) 802.2 D.) Novell-Ether E.) SAP

1 Answers  

---

Which statement about the Point to Point Protocol (PPP) is true? A. PPP supports TCP/IP but not Novell IPX B. PPP is being phased out of existence by the Serial Line Internet Protocol (SLIP) C. PPP providces router to router and host to network connections over both synchronous and asynchronous circuits D. PPP is an ITU T and ANSI standard that defines the process for sending data over a packet switched data network (PSDN)

2 Answers  

---

Identify the command to determine if CDP is enabled? A.) show enable cdp B.) show cdp enabled C.) show cdp run D.) show cdp

1 Answers  

---

What does the term "attenuation" mean in data communication? 1 loss of signal strength as distance increases 2 time for a signal to reach its destination 3 leakage of signals from one cable pair to another 4 strengthening of a signal by a networking device

3 Answers  

---

What is matric?

0 Answers  

---

Which OSI layer provides mechanical, electrical & procedural specifications for activating, maintaining physical link? A.) Presentation B.) Network C.) Application D.) Physical E.) Transport F.) Data-Link

1 Answers  

---

Completely describe the steps based on OSI Model, what happens when you enter the address http://google.com in browser?? Summarize the complete steps based on layered OSI approach.

3 Answers   Cisco, Intel, TCS, Trimble Navigation,

---

Station A is transmitting data to station B, and expects an acknowledgment after every 400 bytes. After transmitting data for a while, the two stations determine the line is reliable and change to expecting and acknowledgement every 600 bytes. This is an example of (pick the best answer only): A.) BECN B.) Sliding Windows C.) Poison Reverse D.) Countdown timers E.) Split Horizon F.) Count to infinity

1 Answers  

---

hi... i am usin packet tracer 5.0.. i hav connect two routers A and B. A has 200.100.25.100 and 1.0.0.1 and router B has 200.100.50.100 and 1.0.0.2... i hav connected 1.0.0.1 and 1.0.0.2... now i want to route 200.100.25.100 and 200.10.50.100 usin rip.. i enable rip in both the routers... but whn i give the command show ip route... i jus get this Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set A# so can sombody tell me where i hav gone wrong... thanku

4 Answers  

---

What is switch priority & why it is used????

5 Answers   ADP,

---

Routers can learn about destinations through static routes, default, or dynamic routing. By default, a router will use information derived from __________. A. IGRP B. RIP C. IP D. TCP

2 Answers   pspl,

---