Interested to Buy Any Domain ? << Click Here >> for more details...
Identify the named IP access-list number range?
A.) 600 - 699
B.) 1 - 99
C.) 900 - 999
D.) 200 - 299
E.) none of the above
- 2 Answers
- 6225 Views
- I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
The answer is B. i-e 1-99. whether you use named access
list or number access list u have to use the number. yes,
if you are asking about standard and extended access list
then my answer would be different then.
But if you use only the B. is the option that you can use
as number or named access list. the rest are not among the
access list ranges because ranges of access lists are
following.
1 to 99 Standard IP
100 to 199 Extended IP
1300 to 1999 Standard IP
2000 to 2699 Extended IP
| Is This Answer Correct ? | 2 Yes | 0 No |
How many valid ip will b in /21 in route summarization?
Which protocol gets a hardware address from a known IP address? A.) RARP B.) TCP C.) IP D.) BootP E.) ARP F.) ICMP
When written <cr > what does it mean?
In transport layer, for connection oriented communication Three way handshake process is there to establish a connection. So question is that, when a host send an ACK messages to another host with host intend to establish a connection, the source host send it as Broadcast or unicast message? Cud anyone explain this. Thanks in advance.
Cisco routers use wildcard masking to identify how to check or ignore corresponding IP address bits. What does setting a wildcard mask bit to 0 cause the router to do? A. It tells the router to check the corresponding bit value. B. It tells the router to ignore the corresponding bit value. C. It tells the router to check its alternate routing list. D. It tells the router to use its primary routing list.
What is the difference between arp and rarp?
Explain the types of communication in ipv6 ?
What is Cisco's default encapsulation method on serial interfaces? A.) ANSI B.) Cisco C.) Q933a D.) HDLC
Identify 3 characteristics of a MAC address? A.) Burned into the NIC B.) 48 bits long C.) Length is 32 bits D.) Used to deliver the frame to the end device E.) Contains a network portion and a host portion
please point out the wrong steps in that l3 switch conf Building configuration…… Current configuration : 1802 byte ! Version 12.2 no service pad Service timestamps debug uptime no service-password encryptions ! hostname xxxx ! enble secret XXXXXXXXXXX(omitted) enable password jitendera kumar sinha ! No aaa new-model System mtu routing 1500 bytes ip subnet-zero ip routing ip name-server 202.x.x.x. ip name –server 203.x.x.x ip name-server 192.168.x.x ip dhcp excluded-address 172.x.x.x 172.x.x.x ! ip dhcp pool ss network 172..x.x.x 255.255.255.0 domain-name xxx.com default-router 172.x.x.x dns-server 192.x.x.x 203..x.x.x 202.x.x.x lease10 ! ! ! ! ! no file verify auto spanning-tree maode pvst spanning-tree extended system-id ! vlan internel allocation policy ascending ! interface fastethernet 0/1 no switch port ip address 172.x.x.x 255.255.255.0 ! interface fastethernet 0/2 no switch port ip address 192.x.x.x ! interface fastethernet 0/3 switcport access vlan 5 switchport mode access ! interface fastethernet 0/4 Switcport access vlan 5 Switchport mode access ! interface fastethernet 0/5 Switcport access vlan 5 Switchport mode access ! interface fastethernet 0/6 Switcport access vlan 5 Switchport mode access ! interface fastethernet 0/7 Switcport access vlan 5 Switchport mode access ! interface fastethernet 0/8 Switcport access vlan 5 Switchport mode access ! interface fastethernet 0/9 Switcport access vlan 5 Switchport mode access ! interface fastethernet 0/10 Switcport access vlan 5 Switchport mode access ! interface fastethernet 0/11 Switcport access vlan 5 Switchport mode access ! interface fastethernet 0/12 Switcport access vlan 5 Switchport mode access ! Interface fastethernet 0/13 Switcport access vlan 5 Switchport mode access ! Interface fastethernet 0/14 Switcport access vlan 5 Switchport mode access ! Interface fastethernet 0/15 Switcport access vlan 5 Switchport mode access ! Interface fastethernet 0/16 Switcport access vlan 5 Switchport mode access ! Interface fastethernet 0/17 Switcport access vlan 5 Switchport mode access ! Interface fastethernet 0/18 Switcport access vlan 5 Switchport mode access ! Interface fastethernet 0/19 Switcport access vlan 5 Switchport mode access ! Interface fastethernet 0/20 Switcport access vlan 5 Switchport mode access ! Interface fastethernet 0/21 Switcport access vlan 5 Switchport mode access ! Interface fastethernet 0/22 Switcport access vlan 5 Switchport mode access ! Interface fastethernet 0/23 Switcport access vlan 5 Switchport mode access ! Interface fastethernet 0/24 Switcport access vlan 5 Switchport mode access ! Interface vlan 1 No ip address Shutdown ! Interface vlan 5 Ip address 172.16.x.x 255.255.255.0 ! Ip default-gateway 172.16.32.1 ! Ip classless Ip route 0.0.0.0 0.0.0.0 fastethernet 0/1 172.x.x.x Ip route 0.0.0.0 0.0.0.0 fasrethernet 0/2 192.168.x.x 254 Ip http-server ! ! Control-plane ! ! Line console 0 Line vty 0 4 Password password Login Line vty 5 15 Password password Login ! end chek out the wrong steps and post it. i ma not able to ping firewall
What command will not display the status of to1? A.) show int to1 B.) show to1 C.) show interface to1 D.) show interface
On which layer does L2F, PPTP and L2TP operate?
CCNA 
