What is Cisco's default encapsulation method on serial
interfaces?

A.) ANSI

B.) Cisco

C.) Q933a

D.) HDLC

Answers were Sorted based on User's Feedback



What is Cisco's default encapsulation method on serial interfaces? A.) ANSI B.) Cisco ..

Answer / guest

Answer: D

Is This Answer Correct ?    68 Yes 3 No

What is Cisco's default encapsulation method on serial interfaces? A.) ANSI B.) Cisco ..

Answer / robert

default encapsulation in serial interface HDLC.
frame relay LMI type Default Cisco we can use ANSI,Q933a.

Is This Answer Correct ?    28 Yes 7 No

Post New Answer

More CCNA Interview Questions

Hi Guys I am facing one problem while configuring PAP over Point to Point links. Configuration scenario is like this. ROUTER 1: (Hostname – R1) R1(config)#username R2 password CCNA2 R1(config)#interface serial 1/1 R1(config-if)ip address 10.0.0.1 255.0.0.0 R1(config-if)#lock rate 64000 R1(config-if)#encapsulation ppp R1(config-if)#ppp authentication pap R1(config-if)#ppp pap sent –username R1 password CCNA1 R1(config-if)#no shutdown ROUTER 2: (Hostname – R2) R2(config)#usename R1 password CCNA1 R2(config)#interface serial 1/1 R2(config-if)#ip address 10.0.0.2 255.0.0.0 R2(config-if)#encapsulation ppp R2(config-if)# ppp authentication pap R2(config-if)# ppp pap sent –username R2 password CCNA2 R2(config-if)#no shutdown Now problem is that, after configure the command “ppp authentication pap” the “Line protocol” status goes down on each router. But when I disable this command using “no ppp authentication pap”, the “Line Protocol” status goes up. What could be the problem, can anyone explain it plzzz….!!! Thanks in Advance…!! Shahin..

6 Answers  


what is bgp i have ansered all of them except mpls while i am working on it but i donot have threotical concepts on it the told me that they are keeping me on hold let try urs knowledge all the best

1 Answers  


what is the main features of link state routing protocols?

1 Answers   Wipro,


How many networks route update does a router recieves in RIP at once ?

3 Answers   ComNet,


which points are eliminated by the DBSCAN algorithm?

0 Answers  






What is name of ospf algo?

0 Answers  


Which of the following provide connection-oriented transport to upper layer protocols? A.) SPX B.) RIP C.) NLSP D.) NCP

1 Answers  


As a system administrator, you need to set up one Ethernet interface on the Cisco router to allow for both sap and Novell-ether encapsulations. Which set of commands will accomplish this? A. interface ethernet 0.1 ipx encapsulation Novell-ether ipx network 9e interface ethernet 0.2 ipx network 6c B. interface ethernet 0 ipx encapsulation Novell-ether ipx network 9e interface ethernet 0 ipx encapsulation sap ipx network 6c C. interface ethernet 0.1 ipx encapsulation Novell-ether interface ethernet 0.2 ipx encapsulation sap D. interface ethernet 0.1 ipx encapsulation Novell-ether ipx network 9e interface ethernet 0.2 ipx encapsulation sap ipx network 6c

1 Answers  


Can you explain PPTP (Point-to-Point Tunneling Protocol)?

1 Answers   CCIE,


Which of the following is a valid TCP/IP socket for an Email connection? 101.34.2.125:25 00-00-03-1B-CA-6F:143 202.167.23.101:21 60.4:110

2 Answers  


How many LMI types are available on Cisco routers? A.) Four B.) Two C.) Five D.) Three

3 Answers  


Which command successfully pings an individual IP address? A. Router> ping 192.5.5.0 B. Router# ping 192.5.5.30 C. Router> ping 192.5.5.256 D. Router# ping 192.5.5.255

2 Answers  


Categories