Which commands would assign and enable IPX on an interface ?
A.) enable netware
B.) enable novell-ether
C.) router#(config)ipx routing
D.) You must first enable IPX globally and then
assign the network number to the interface .
E.) enable ipx
F.) router#(config-if)ipx network 4a
- 1 Answers
- 3042 Views
- I also Faced
- E-Mail Answers
Which of the following is an example of the Network Layer? A.) Token Ring B.) RARP C.) LLC D.) DDP E.) TCP
Which command will show you if you have a DTE or DCE cable connected to an interface?
Assume that you are editing a line of text on a Cisco router. What key-stroke combination would take you to the beginning of the line? A.) CTRL-B B.) CTRL-Z C.) CTRL- D.) CTRL-A E.) CTRL- F.) CTRL-
Which of the following are ways to provide login access to a router? A.) HTTP B.) Console C.) Telnet D.) Aux Port E.) SNMP F.) LLC
You have powered on a new router and you want to create an initial configuration. Which mode should you use? A. copy mode B. user mode C. setup mode D. startup mode
Which command will give the following output: Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int * 0 CTY - - - - - 0 0 0/0 - 1 AUX 9600/9600 - - - - - 0 0 0/0 - * 2 VTY - - - - - 2 0 0/0 - 3 VTY - - - - - 0 0 0/0 - 4 VTY - - - - - 0 0 0/0 - 5 VTY - - - - - 0 0 0/0 - 6 VTY - - - - - 0 0 0/0 -
How many LMI types are available on Cisco routers? A.) Four B.) Two C.) Five D.) Three
Which of the following describe full-duplex transmission? A.) Uses a single wire B.) Data transmission in only both directions, but only one way at a time C.) Uses a point-to-point connection from the transmitter of the transmitting station to the receiver of the receiving station D.) Data transmission in only one direction
hi friends i have a problem.plz solve this. i am working some where and i have the number of swtitch.once my project manger says that we are going to exapnd our number of employ so plz attech an another switch.i asked to my jr network engineer that take a witch and implemnt on that n/w,as he implement the switch on that n/w.thats network get down, plz tell me what is the reason of that.
Tell me which multicast ip eigrp protocol use?
please point out the wrong steps in that l3 switch conf Building configuration…… Current configuration : 1802 byte ! Version 12.2 no service pad Service timestamps debug uptime no service-password encryptions ! hostname xxxx ! enble secret XXXXXXXXXXX(omitted) enable password jitendera kumar sinha ! No aaa new-model System mtu routing 1500 bytes ip subnet-zero ip routing ip name-server 202.x.x.x. ip name –server 203.x.x.x ip name-server 192.168.x.x ip dhcp excluded-address 172.x.x.x 172.x.x.x ! ip dhcp pool ss network 172..x.x.x 255.255.255.0 domain-name xxx.com default-router 172.x.x.x dns-server 192.x.x.x 203..x.x.x 202.x.x.x lease10 ! ! ! ! ! no file verify auto spanning-tree maode pvst spanning-tree extended system-id ! vlan internel allocation policy ascending ! interface fastethernet 0/1 no switch port ip address 172.x.x.x 255.255.255.0 ! interface fastethernet 0/2 no switch port ip address 192.x.x.x ! interface fastethernet 0/3 switcport access vlan 5 switchport mode access ! interface fastethernet 0/4 Switcport access vlan 5 Switchport mode access ! interface fastethernet 0/5 Switcport access vlan 5 Switchport mode access ! interface fastethernet 0/6 Switcport access vlan 5 Switchport mode access ! interface fastethernet 0/7 Switcport access vlan 5 Switchport mode access ! interface fastethernet 0/8 Switcport access vlan 5 Switchport mode access ! interface fastethernet 0/9 Switcport access vlan 5 Switchport mode access ! interface fastethernet 0/10 Switcport access vlan 5 Switchport mode access ! interface fastethernet 0/11 Switcport access vlan 5 Switchport mode access ! interface fastethernet 0/12 Switcport access vlan 5 Switchport mode access ! Interface fastethernet 0/13 Switcport access vlan 5 Switchport mode access ! Interface fastethernet 0/14 Switcport access vlan 5 Switchport mode access ! Interface fastethernet 0/15 Switcport access vlan 5 Switchport mode access ! Interface fastethernet 0/16 Switcport access vlan 5 Switchport mode access ! Interface fastethernet 0/17 Switcport access vlan 5 Switchport mode access ! Interface fastethernet 0/18 Switcport access vlan 5 Switchport mode access ! Interface fastethernet 0/19 Switcport access vlan 5 Switchport mode access ! Interface fastethernet 0/20 Switcport access vlan 5 Switchport mode access ! Interface fastethernet 0/21 Switcport access vlan 5 Switchport mode access ! Interface fastethernet 0/22 Switcport access vlan 5 Switchport mode access ! Interface fastethernet 0/23 Switcport access vlan 5 Switchport mode access ! Interface fastethernet 0/24 Switcport access vlan 5 Switchport mode access ! Interface vlan 1 No ip address Shutdown ! Interface vlan 5 Ip address 172.16.x.x 255.255.255.0 ! Ip default-gateway 172.16.32.1 ! Ip classless Ip route 0.0.0.0 0.0.0.0 fastethernet 0/1 172.x.x.x Ip route 0.0.0.0 0.0.0.0 fasrethernet 0/2 192.168.x.x 254 Ip http-server ! ! Control-plane ! ! Line console 0 Line vty 0 4 Password password Login Line vty 5 15 Password password Login ! end chek out the wrong steps and post it. i ma not able to ping firewall
Differentiate full-duplex from half-duplex.
CCNA 
