Which two of the following protocols are used at the
Transport layer?

A.) ARP

B.) UDP

C.) ICMP

D.) RARP

E.) TCP

F.) BootP

Answers were Sorted based on User's Feedback



Which two of the following protocols are used at the Transport layer? A.) ARP B.) UDP C.) ..

Answer / goivnd

B.) (udp) unrealible protocol
E.) (tcp) realible protocol

Is This Answer Correct ?    1 Yes 0 No

Which two of the following protocols are used at the Transport layer? A.) ARP B.) UDP C.) ..

Answer / guest

Answer: B E

Is This Answer Correct ?    0 Yes 0 No

Which two of the following protocols are used at the Transport layer? A.) ARP B.) UDP C.) ..

Answer / mintoo ch

.) UDP
.) TCP

Is This Answer Correct ?    0 Yes 0 No

Which two of the following protocols are used at the Transport layer? A.) ARP B.) UDP C.) ..

Answer / mintoo ch

.) UDP
.) TCP

Is This Answer Correct ?    0 Yes 0 No

Which two of the following protocols are used at the Transport layer? A.) ARP B.) UDP C.) ..

Answer / m haja bahurudeen

Ans : B,E


TCP,UDP - Layer4

ICMP - Layer3

Is This Answer Correct ?    0 Yes 0 No

Which two of the following protocols are used at the Transport layer? A.) ARP B.) UDP C.) ..

Answer / sandeep dahayat

Answer:- B.) & E.)

UDP and TCP used at the Transport Layer

Is This Answer Correct ?    0 Yes 0 No

Which two of the following protocols are used at the Transport layer? A.) ARP B.) UDP C.) ..

Answer / sanjeev sharma

ANS IS UDP AND TCP BOTH ARE USED ON TRANSPORT LAYER BUT AT
A TIME WE CAN USE ONLY ONE PROTOCOL UDP OR TCP .......THANKS

Is This Answer Correct ?    0 Yes 0 No

Post New Answer

More CCNA Interview Questions

What is the Function of Router?

5 Answers  


What is a back off on an 802.3 networks? A. It is latency in store and forward switching B. It is the time used for token passing from machine to machine C. It is the retransmission delay that is enforced when a collision occurs D. It is the result of two nodes transmitting at the same time. The frames from each transmitting device collide and are damaged

1 Answers  


Identify the keystroke used to terminate the setup mode? A.) Ctrl-K B.) Crtl-C C.) Ctrl-Z D.) Crtl-End

1 Answers   Cisco, HCL,


Which of the following would not be displayed by the command ?sho cdp neighbor detail?? A.) The incoming/outgoing interface. B.) The hardware platform. C.) One address per protocol. D.) Amount of Flash Memory Available E.) The routers hostname. F.) The subnet mask, if IP is configured.

1 Answers  


Identify the command to determine if an IP access-list is grouped on interface e0? A.) Router(config)# show ip interface e0 B.) Router> show ip interface e0 C.) Router# show interface e0 D.) Router# show ip interface e0

1 Answers  






How many types of nat?

0 Answers  


When dr communicate with bdr which multicast ip it use?

0 Answers  


Which feature should a routing protocol have to support vlsm?

0 Answers  


Identify the command to display the IP routing table? A.) show route B.) show ip route C.) show ip table route D.) show ipx route

1 Answers  


Which processes does TCP, but not UDP, use? A. Windowing B. Acknowledgements C. Source Port D. Destination Port

2 Answers   Lucent,


Which layer defines bit synchronization? A.) Application B.) Network C.) Transport D.) Physical E.) Session F.) Session

2 Answers  


Identify the X.25 addressing standard? A.) X.121 B.) X.25a C.) ITU-1 D.) Q933a

1 Answers  


Categories