Answer / guest

Answer: B

Identify the command mode necessary to enter the standard ping command? A.) Router(config)# B.) Router> C.) Router(std-ping)# D.) Router(config-if)#

1 Answers  

---

hi friend i hav difficulty n need to solve it...v need to implement a new raw switch in company as to increase the no of staff...snc raw switch by default is in server mode,i wanna know 1.how to make a switch in client mode...2.how to configure switch i mean to sy how to connect all switches to network.

3 Answers  

---

Identify the extended IP access-list number range? A.) 600 - 699 B.) 1 - 99 C.) 900 - 999 D.) 100 - 199

2 Answers  

---

When setting up a WAN network, everything outside of the Demarc is not owned by the customer. Which of the following are not owned by the customer? A.) The T1 line. B.) LAN C.) The Router D.) DTE E.) PC's F.) CO

1 Answers  

---

Identify the command to determine if CDP is enabled? A.) show enable cdp B.) show cdp enabled C.) show cdp run D.) show cdp

1 Answers  

---

Identify the command to display the IP routing table? A.) show route B.) show ip route C.) show ip table route D.) show ipx route

1 Answers  

---

Which statement about the Committed Information Rate (CIP) is true? A. It is the rate in bits per second at which the Frame Relay switch agrees to transfer data B. It is the clock speed (pod speed) of the connection (local loop) to the Frame Relay cloud C. It is the maximum number of bits that switch can transferduring any Committed Rate Measurement Interval D. It is a signaling standard between the 3PE device and FP switch. It is responsible for managing the connection and maintaining status between the devices.

1 Answers  

---

What is the difference between TCP and UDP? A.) TCP is connection-oriented; UDP uses acknowledgements only B.) TCP is connection-oriented; UDP is connectionless C.) Both TCP and UDP are connection-oriented, but only TCP uses windowing D.) TCP and UDP both have sequencing, but UDP is connectionless

2 Answers  

---

what is the major difference between EIGRP & IGRP?

9 Answers   Wipro,

---

take a pen and copy before solving that question there is a router name Ra there is two switch sw1 and sw2 sw1 is coneceted through fa0/1 interface of router Ra sw2 is conected through the fa1/1 serai interface of router s0/1 conected through the isp with it ip address 192.168.1.1 now therer are three host conexted through the sw1 and having ip host1=10.1.2.1 host2=10.1.2.2 host3=10.1.2.3 now there is also 3ree host conected through switch 2 i.e sw2 having ip host4=10.1.1.1 host 5=10.1.1.2 host 6=10.1.1.3 now i think u have made corect confrigation.now questios is started network admin configure the Ra router in that fassion Ra(config)#access-list 2 permit 10.1.1.0 0.0.0.255 Ra(config)#line vty 0 4 ra(config)#access-class 2 in now question is that why should network admnistratoe do it in this maneer A to give access sw1 host to acess internet B to prevent sw1 host from acessing comand promt c to prevent sw2 host from accessing console of router ra D to give sw2 host access to the enternet e prevent sw1 host from accessing internet f to prevent sw1 host from acessing the sw2 host network isp------(s0/1)..RA..(fa1/1)---SW2-host (4,5,6) | | (sw1)------host 1,2,3 this is not exect digarm but help to derive the diagram plz answer as soon as possible

6 Answers   AT&T,

---

Which statement is true regarding full duplex? A.) Allows for transmission and receiving of data simultaneously B.) Only works in a multipoint configuration C.) Does not affect the bandwidth D.) Allows for transmission and receiving of data but not at the same time

2 Answers  

---

Which of the following are examples of the Datalink Layer? A.) LLC B.) SQL C.) TCP D.) Token Ring E.) IP

2 Answers  

---