Interested to Buy Any Domain ? << Click Here >> for more details...
Which two of the following are valid ways to have multiple
encapsulation types on a single interface?
A.) This is not possible
B.) subinterfaces
C.) additional physical interfaces
D.) secondary addresses
- 2 Answers
- 5050 Views
- I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / guest
Answer: B D
Cisco routers do not allow multiple encapsulation types on a
single
interface. Therefore, it is necessary to create either a
Secondary
Network, or a Subinterface and assign a new encapsulation type.
| Is This Answer Correct ? | 3 Yes | 1 No |
Answer / rd_bharwani
It would be only B...
which would creat a subinterface
| Is This Answer Correct ? | 0 Yes | 1 No |
What is the purpose of ARP? A.) IP to host name resolution B.) Host name to IP address resolution C.) Mac to IP address resolution D.) IP to Mac address resolution
4 Answers Cordys, Punjabi University,
Identify the command to display the IP routing table? A.) show route B.) show ip route C.) show ip table route D.) show ipx route
Tell me how many reserve ports?
The command 'debug ip rip' will do which of the following? A.) Show Neighbor Info. B.) Display RIP routing updates. C.) Show routing table changes. D.) Show all IP traffic. E.) This is not a valid router command. F.) Cause the router to respond with 'Ambiguous command'
Which two statements are true? (Choose two) A. Ethernet 802.3 utilizes a half duplex method for data transfer B. In a 100 MBS point to point connection a full duplex connection can provide 400 Mbs of data transfer C. Ethernet switches can use the full duplex mode to connect multiple nodes on a single pod of a switch D. Full duplex Ethernet takes advantage of UTP using one pair for transmission and the other pair for reception
LMI operates between the Frame Switch and what other device? A.) CPE device B.) Another Frame Switch C.) X.25 switch D.) Novell File Server
What does the acronym ARP stand for? A.) Address Resolution Phase B.) ARP Resolution Protocol C.) Address Resolution Protocol D.) Address Recall Protocol
At which layer of the OSI model does the ping command operate? A. session B. network C. transport D. maintenance
12 Answers EF, IBM, jetking, Nexlinx, Rkd, TCS, Wipro,
CCNA question and answer only for networking.
Identify the named IP access-list number range? A.) 600 - 699 B.) 1 - 99 C.) 900 - 999 D.) 200 - 299 E.) none of the above
hi i am facing one problem.ptoblem is like that i am getting output error on mine router ethernet interfae here is the cisco#show interface e0 Ethernet0 is up, line protocol is up Hardware is QUICC Ethernet, address is 0030.802d.2a17 (bia 0030.802d.2a17) Internet address is 202.122.20.225/28 MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec) ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:00, output 00:00:00, output hang never Last clearing of "show interface" counters 05:55:07 Queueing strategy: fifo Output queue 0/40, 0 drops; input queue 0/75, 0 drops 5 minute input rate 10000 bits/sec, 11 packets/sec 5 minute output rate 29000 bits/sec, 11 packets/sec 1515202 packets input, 359100396 bytes, 1 no buffer Received 6 broadcasts, 0 runts, 0 giants, 1 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 0 input packets with dribble condition detected 1584394 packets output, 1623395338 bytes, 0 underruns 1820 output errors, 26732 collisions, 0 interface resets 0 babbles, 0 late collision, 9698 deferred 18 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out output cisco# what is the reason how to solve this please tell me i am using cisco asa 5520 behid mine internet router and no error on the asa inside interface
Which device listed below provides clocking for the line? A.) DCE B.) CPE C.) CO D.) DTE E.) Demarc
CCNA 
