Interested to Buy Any Domain ? << Click Here >> for more details...
Windowing is a type of?
A.) Negative acknowledgement
B.) Address resolution
C.) Layer transition mechanism
D.) Flow control
- 1 Answers
- 4855 Views
- Redington, I also Faced
- E-Mail Answers
Answer / guest
Answer: D
Windowing allow the sender and receiver to dictate how much
information
that can be received prior to an acknowledgement. It is a
form of flow
control.
| Is This Answer Correct ? | 2 Yes | 0 No |
What is the size of hello packets in eigrep protocol?
GUY i Have attended one interview for the data craft and they are offering me L1 postion and i am working at l2 in cisco so there is no way to get in the datacraft i am posting here the question he asked to and i have tested the interviewer and i come to know he was not having any knowledge. His questions are-: 1) what is Vlan 2) what is stp and what is difference between stp and RSTP 3) what is HSRP and Diffrence betwwen HSRP and GLBP 4) how to configure HSRP 5) Scenario Based question ( if we have two router and both are connected and there are having redundancy means two interface of the router r1 is connected to the two interface of Router R2 (R1)-------------(R2 (R1)-------------(R2 Now he want to configure the router in such a Manner that if one link down second link should come up.My answer was HSRP and his is "F looting static routing was i wrong "i know F looting Static routing is Theoretically possible but it is not fusible in the scenario where you have multiple router connected to the same router and if you have configured sub interface i challenged him and he lost The Battle and he get angary 5) what the eigrp and how it works 6) tables in eigrp 7) the information of feasible successor where it saved now after answering these all he was very angry ( i can fill the heat) 8) then he come to ospf Area type ( he was also not aware) 9) LSA type and its working ( he was also having confusion ) 10) then is asked routing by rummer( Theroy) 11) hello and dead intervel of EIGRp (theory) 12) Selection cretaria for Eigrp slecting best path ( here we have a long discussion on MTU and he lost the battle and agree That MTU never comes in the accounts in this process) 13) what is ACL type of acl ( here he was aware of TWO type Standard and extended i have told him 5 type( he again get Angry) We have 2hr of discussion and and he told me he will call me latter but i know he never call
Identify the 2 rules used when configuring a Distance Vector routing protocol? A.) Physically connected network(s) B.) Configure the classfull address, no subnets C.) Enable CDP so neighbors can be detected D.) Same autonomous network
A banana plantation is located next to a desert. The plantation owner has 3000 bananas that he wants to transport to the market by camel, across a 1000 kilometre stretch of desert. The owner has only one camel, which carries a maximum of 1000 bananas at any moment in time, and eats one banana every kilometre it travels. What is the largest number of bananas that can be delivered at the market?
Identify the command that configures the bandwidth to 56K? A.) Router(config-if)# bandwidth 56000 B.) Router(config-if)# bandwidth 56k C.) Router(config)# bandwidth 56 D.) Router(config-if)# bandwidth 56
What is the difference between simple authentication and md5?
what is hop count?
the situation iz like ths -at a specific time in our company the internet connectivity goes off...v hav two networks in our company...but out of it only one link goes down for 5-10 sec...a fastethernet port becomes down for few sec and automatically becomes Up... Is this occures becoz of Power?? If yes thn y the 2nd network is not affected??
Which 3 statements describe default encapsulation and LMI type configuration? A.) There are only 4 encapsulations and 3 LMI type options B.) The LMI type config term options C.) In release 11.2 the LMI type is autosensed D.) The default LMI is Cisco E.) IETF encapsulation must be configured unless the connecting routers are both Cisco
What does the trace response !H mean? * A: Network unreachable * B: Not forwarded due to ACL restriction * C: Protocol unreachable * D: Port could not be reached
Hi, Shahin Thanks a lot for providing me these sites. These links are really helpful for me. r u working somewhere please let me know
can we measure how much a host exact bandwidth using by a network cable which is communicating over the network? options: 1- via Router 2- Switch, 3- other device... if yes.. then how ( with every option)
CCNA 
