Golgappa.net | Golgappa.org | BagIndia.net | BodyIndia.Com | CabIndia.net | CarsBikes.net | CarsBikes.org | CashIndia.net | ConsumerIndia.net | CookingIndia.net | DataIndia.net | DealIndia.net | EmailIndia.net | FirstTablet.com | FirstTourist.com | ForsaleIndia.net | IndiaBody.Com | IndiaCab.net | IndiaCash.net | IndiaModel.net | KidForum.net | OfficeIndia.net | PaysIndia.com | RestaurantIndia.net | RestaurantsIndia.net | SaleForum.net | SellForum.net | SoldIndia.com | StarIndia.net | TomatoCab.com | TomatoCabs.com | TownIndia.com
Interested to Buy Any Domain ? << Click Here >> for more details...


The following selections show the command prompt and the

configuration of the IP network mask. Which two are

correct?

A. Router#term IP netmask-format { bitcount | decimal |
hexadecimal }

B. Router(config-if)#IP netmask-format { bitcount | decimal
| hexadecimal }

C. Router(config-if)#netmask-format { bitcount | decimal |
hexadecimal }

D. Router#ip netmask-format { bitcount | decimal | hexadecimal }

Answers were Sorted based on User's Feedback



The following selections show the command prompt and the configuration of the IP network mask. Wh..

Answer / guest

Answer: A & B

Router#term IP netmask-format { bitcount |

decimal | hexadecimal } and Router(config-if)#IP

netmask-format { bitcount | decimal | hexadecimal } are

correct. You can configure the mask for the current session

and you can configure it for a specific line.

Is This Answer Correct ?    5 Yes 2 No

The following selections show the command prompt and the configuration of the IP network mask. Wh..

Answer / ahmed shahin

The answer will be : B & C

B. Router(config-if)#IP netmask-format { bitcount | decimal
| hexadecimal }

C. Router(config-if)#netmask-format { bitcount | decimal |
hexadecimal }

Because we must be under the configuration prompt to
configure this netmask-format

Is This Answer Correct ?    1 Yes 1 No

Post New Answer

More CCNA Interview Questions

Hi Friend. i have to let you know that now i have been selected for cisco india in bangalore. i am thanking to all of you guys that u have been posted such good question and the respective answer. from today i will be not able to visit this site on regular basic and hopeing that you will continue to post the question.the question you are posting is not very usefull to you but also usefull to another. i am again thanking to all of you and hope for best for your feature. Jitendera kumar sinha Network engineer-L2 cisco india Bangalore

0 Answers  


What is the maximum hop count for Link-State protocols? A.) 15 B.) there is no hop count limit C.) 256 D.) 16

1 Answers  


bWhich form of PPP error detection on Cisco routers monitors data dropped on a link? A. Quality B. Magic Number C. Error Monitor D. Droplink

1 Answers  


When written <cr > what does it mean?

0 Answers  


What type of transmission bus topology support?

0 Answers  


What does a router do with a packet that it does not have a destination network for? A.) Sends it to the Serial port B.) Drops the packet C.) Sends it back out the same interface it received it in D.) Forwards the packet to the next hop

2 Answers  


What are the different memories used in a CISCO router?

0 Answers  


Windowing is a type of? A.) Negative acknowledgement B.) Address resolution C.) Layer transition mechanism D.) Flow control

1 Answers   Redington,


What is the easiest way to remotely configure a router?

0 Answers  


What is the difference between arp and rarp?

0 Answers  


Which command sets IGRP as the routing protocol for autonomous system 100? A. Router(config)#igrp 100 B. Router(config)#network 100 C. Router(config)#router igrp 100 D. Router(config)#enable igrp 100

1 Answers  


What command would you use to find out the names of Novell servers on a network? A. show ipx servers B. show ipx hosts C. show ipx sap D. show ipx nodes.

1 Answers  


Categories