Answer / bhumi

An accumulator is an 8-bit register that is a part of ALU
(Arithmatic-Logic Unit) of a processor.It is used for
temporary storage of 8-bit data and to perform arithmatic
operations like addition,subtraction,multiplication,division
or logical operations like AND,OR,XOR etc.The result of
operation is stored in accumulator.

Answer / eng/khalid abdo

A hydraulic accumulator is an energy storage device. It is a
pressure storage reservoir in which a non-compressible
hydraulic fluid is held under pressure by an external
source. That external source can be a spring, a raised
weight, or a compressed gas. The main reasons that an
accumulator is used in a hydraulic system are so that the
pump doesn't need to be so large to cope with extremes of
demand, so that the supply circuit can respond more quickly
to any temporary demand and to smooth pulsations.

Answer / irshad

The accumulator is an 8-bit register. It can send or
receive data via internal data bus.
It holds one of the quantities to be operated on by the ALU
and receives the result of an operation done by the ALU.
The accumulator is also identified as register A.

Answer / deepak kumar agrawal

accumulator is a device which is situated after evaporator.
it;s function to protect compressor from liquid flooding.

Answer / manikumar

The accumulator used for balancing presser control
hydraulic pump to working cylinder at time of cylinder
working contsion.

Answer / satya

A hydraulic accumulator is an energy storage device. It is a
pressure storage reservoir in which a non-compressible
hydraulic fluid is held under pressure by an external
source. That external source can be a spring, a raised
weight, or a compressed gas. The main reasons that an
accumulator is used in a hydraulic system are so that the
pump doesn't need to be so large to cope with extremes of
demand, so that the supply circuit can respond more quickly
to any temporary demand and to smooth pulsations.

Answer / m.sujith

basically accumulator is the primary register for ALU. its
primary function to hold the first data of operation which
is performed/processed by the ALU. After the successful
operation done by the ALU , the accumulator act as
repository by replacing the input data by results and then
Accumulator transferred the result to memory or output
device according to the instruction.

repository-maintained or stored

Answer / hemant

accumulator is a device which is prohibited the liquid
particals entering in compressor, it's use for safty of
compressor , because compressor is damage by liguid paticals.
in accumulator have many resister who
prohibited the liquid particals and only vapour refrigerent
pass into the compressor.

Answer / dr.v.jaiganesh

It accumulates the partial allowance of vapour refrigerant
and also control the flow of vapour refrigrant to the
compressor

Answer / priya

Accumulator is register simply.. . It performs 2 functions.. if the operation (a+b) is performed..1) one of the two operands will be stored .. 2) result of the operation will be stored

Describe the general purpose registers of 8085?

0 Answers  

Difference between 80286 and 80287

2 Answers   Mascot,

Explain the software instruction ei and di?

0 Answers  

Explain what is microcontroller?

0 Answers  

What is the purpose of a buffer register in reference to 8085?

0 Answers  

Give example of bit address and byte address?

0 Answers  

Signal voltage ranges for a logic high and for a logic low in RS-232C standard are

0 Answers   CDAC,

What is stack pointer?

0 Answers  

What is the purpose of the biu in the 8086?

0 Answers  

Describe the (status) flag register of 8085?

0 Answers  

load a mul a store t1 load b mul b store t2 mul t2 add t1 then the content in accumulator is

2 Answers   Wipro,

write the assembly language programming to find the 2's complement for a string of 100 bytes

0 Answers