Mechanical Engineering Interview Questions, Answers for Freshers and Experienced asked in various Company Job Interviews

Mechanical Engineering Interview Questions

Questions Answers Views Company eMail

why should carrnot cycle not use in practicale

3 5497

how can calculate the hight of chimny in a power plants

4 6402

What is seamless pipe

Armco,

4 8189

How much fuel is to be burn for production of 1 ton steam?

1920

How much steam is to be required for generation of 1MW electricty?

Ennore Coke, Uttam Galva,

6 9863

What to write.. for perception about ntpc.. when you are applying for its interview?

NTPC,

1991

What to write.. for perception about ntpc.. when you are applying for its interview?

NTPC,

1 4719

what are the advantages of PID controllers compared with those of a PLC

Bhel,

2 5811

what is the difference between limit of proportionality and elastic limit minimum 8 differences???? plz answer this question as quickly as possible

2 12903

why stress relieving of stainless steel is not preffered

Imperial Auto, L&T,

2013

ongc technical questions in mechanical engineering

ONGC,

1 4900

Can i get technical questions asked in ADANI Power?????

Adani, Adani Power, GJ,

2 21628

Assume a DC motor with the following parameters : Motor torque control = 0.0848 Nm/amperes Back EMF control = 0.0848 Volts/(rad/s) Armature resistance = 0.75  Moment of inertia = 0.00001696 kg/m2 With zero frictional load and taking a feed forward gain of 2, determine the motor response for a unit step function. please forwaded the answer to the below mail id thanks in advance Regrads, peer_kaba@yahoo.co.in

Ignou,

1927

What is cutt off ratio in IC Engines.give proper defination.

Essar, Hyundai, Jindal Steel and Power, L&T,

5 43775

which is heavier 1kg. of iron or 1kg. of cotton?and why?

Getco, Jindal, Lloyd, Naval Academy, NDA, samr, swiggy,

33 108685

Post New Mechanical Engineering Questions

Un-Answered Questions { Mechanical Engineering }

When repacking a valve the rings of packing should be oriented so that the packing ends are installed ____________.

2207

what is the basic optimal difference among isothermal,isentropic and adiabatic processess( with charts of each)??

2177

What is a stage in a steam turbine?

1062

The efficiency of a pin fin with insulated tip is

1743

sir,i m mech. engg final year student, please send me technical test question with answer for gail,bhel,sail& also useful for other psu exam. thank you....

1938

describe a type when u anticipated potential problems and development of preventive measure.

1846

what is the actual difference between casting and moulding? explain pressure die casting process?

18795

why is cast iron seasoning important before machining?

1583

Can I use motor oil in a hydraulic system?

1020

What is gtsc technology?

2234

pls tell me the process to set up a power plant right from the permission from state govt ????

2043

How to start water tube steam boiler

1841

Action plan to closr NCR (NON COONFORMANCE REPORTS)

2237

Hello Friends I had my ONGC test today,but it was very bad.But I would give certain suggestions so that u may not face he problem which i had. Be thorough with Electrical Technology.Generators.motors stators etc.There are 5 questions on that. There were also good no.of questions from Hydraulic machine and Production technology. Then 3 from Strength of materials.And remember the dimensional quantities.

1932

hai this is sreenu...i also applied for the post of PO in syndicate bank..

1979

For More Un-Answered { Mechanical Engineering } Questions Click Here