Interested to Buy Any Domain ? << Click Here >> for more details...
Identify the command to configure the configuration-register? A.) Router# config-register 0x2102 B.) Router(config)# config-register 0x2102 C.) Router(config-reg)# 0x2102 D.) Router> config-register 0x2102
2 6283Identify the command to disable CDP on an interface? A.) Router(config-if)# no cdp enable B.) Router(config-if)# no cdp run C.) Router# no cdp enable D.) Router(config-if)# no cdp
1 6135Identify the command that will display the RIP routes entering and leaving the router? A.) Router(config)# debug ip rip B.) Route# debug ip rip C.) Router>debug ip rip D.) Router# debug rip routes
1 4131Identify the prompt displayed if in privileged exec mode? A.) Router(config)# B.) Router# C.) Router> D.) Router(priv)#
2 6700'Show cdp neighbors detail' show the following 3 pieces of information? A.) Hardware platform B.) Software version C.) Same as 'show version' command D.) Up to 1 address for each protocol E.) Non-direct connected routers
2 5711Identify the command mode necessary to enter the standard ping command? A.) Router(config)# B.) Router> C.) Router(std-ping)# D.) Router(config-if)#
1 5184Identify the command to run 'setup'? A.) Router(config)#setup B.) Router?setup C.) Router#setup D.) Router>setup
1 3870Identify the command that configures serial0 for PPP encapsulation? A.) Router(config)# encapsulation ppp B.) Router(config-if)# encapsulation serial ppp C.) Router(config-if)# encapsulation ppp D.) Router# encapsulation ppp
1 4666Identify the command to display the status of the Frame Relay virtual circuit? A.) Router# show frame-relay virtual-circuit B.) Router(config)# show frame-relay pvc C.) Router# show frame-relay pvc D.) Router# show virtual
1 3985Identify the command that disables name-to-address translation? A.) Router(config-dns)# no ip domain-lookup B.) Router(config)# no address translation C.) Router(config)# no ip domain-lookup D.) Router(config)# ip domain-lookup
1 3837What command will not display the status of to1? A.) show int to1 B.) show to1 C.) show interface to1 D.) show interface
1 4389Identify the 2 commands to copy a configuration from a TFTP server to RAM? A.) configure network B.) configure overwrite C.) copy backup-config running-config D.) copy tftp running-config
2 5051Identify the following command to configure a secret password to 'cisco'? A.) Router(config)#enable password cisco secret B.) Router(config)#enable secret cisco C.) Router(config)#enable secret password cisco D.) Router(config)#set secret = cisco
1 4460Identify the effect of Ctrl-Z? A.) Exits back to privileged exec mode B.) Disconnect from the router C.) Abort the ping operation D.) Exits privileged exec mode
1 4925Given an IPX network with redundant paths, what command will configure load balancing? A.) ipx load-balance B.) ip maximum-paths 2 C.) ipx maximum-paths 2 D.) ipx load-share
1 4302
What is the difference between hub, switch, and router?
What is point-to-point protocol in ccna?
What is the difference between static and dynamic ip addressing?
In which protocol supenetting is enable by default?
What is the default behavior of access-list?
What is the working of router?
What is the usage of service password encryption?
What is the difference between cross cable and straight cable?
What is an autonomous system?
In stead of 0.0.0.0 wild card mask what you can write after ip?
What is ospf? Describe it.
Which decision called socket base?
Which feature should a routing protocol have to support vlsm?
What is the multicast routing?
How many broadcast domains are in switch?
