You have two Cisco routers setup back-to-back in a lab using DTE/DCE cables. To which router would you add the clockrate command? A.) The serial port on the DCE router B.) The Ethernet port on the DTE router C.) The Ethernet port on the DCE router D.) The serial port on the DTE router
How does a switch use store and forward? A.) By using a Class I repeater in a collision domain B.) The LAN switch copies the entire frame into its onboard buffers and then looks up the destination address in its forwarding, or switching, table and determines the outgoing interface C.) By using broadcast addresses as source addresses D.) The switch waits only for the header to be received before it checks the destination address and starts forwarding the packets1 4238
Which of the following are valid WAN terms? A.) DTE B.) DCE C.) Demarc D.) CPE1 2691
Which two describe frame tagging? A.) Examines particular info about each frame B.) A unique ID placed in the header of each frame as it traverses the switch fabric C.) A user- assigned ID defined to each frame D.) The building of filter tables1 3696
A ISDN BRI circuit can be described as a which of the following? A.) 3B channels B.) 2-64Kbps B channels and 1-16Kbps D channel C.) none of the above D.) 2-64Kbps B channels and 1-16Kbps C channel1 2804
The two sublayers of the IEEE Data Link Layer are which of the following? A.) Link and Logical Control B.) Data Link and LLC C.) Logical Link Control and Media Access Control D.) Data Link and MAC3 11307
The -- terminal no editing -- command will perform what function? A.) Edit the contents of NVRAM B.) Allows access to the terminal port C.) Stops the advanced editing feature D.) Enable password functions2 7746
Which two of the following are valid ways to have multiple encapsulation types on a single interface? A.) This is not possible B.) subinterfaces C.) additional physical interfaces D.) secondary addresses2 3231
Which 3 statements describe default encapsulation and LMI type configuration? A.) There are only four encapsulations and 3 LMI type options B.) The LMI type config term options C.) In release 11.3 the LMI type is autosensed D.) The default LMI is Cisco E.) IETF encap must be configured unless the connecting routers are both cisco1 3664
Which can be true regarding VLANs? A.) They are created by location B.) They are created by function C.) They are created by department D.) They are created by group1 4822
What is true when using DDR? A.) HDLC is the preferred encapsulation B.) You must use static routing C.) You should use dynamic routing D.) You should use ISDN1 2325
If you are running Token Ring with Novell IPX routing, which encapsulation should you use? A.) SAP B.) SNAP C.) 802.5 D.) 802.21 2455
What are the 3 ways routers learn paths to destination networks? A.) Dynamic B.) Static C.) Routing tables D.) Default2 15526
Bridges work at what layer of the OSI model? A.) Data Link B.) Network C.) Physical D.) Application12 54785
What is the default switching method for the Cisco 5000 series? A.) Cut-through B.) Store-and-splice C.) Latency D.) Store-and-forward1 4082
What is the mesh network?
What is a vlan?
Explian what is a node?
How does cut-through LAN switching work?
Which ipsec rule is used for the olympia branch and what does it define?
How many types of ends in wan?
What is quality of ipv6?
Which peer authentication method and which ipsec mode is used to connect to the branch locations?
What type of transmission bus topology support?
Does a bridge divide a network into smaller segments?
Which protocol supenetting is enable by default?
What are some standards supported by the Presentation layer?
Differentiate User Mode from Privileged Mode?
What are the things that can be accessed in a CISCO router’s identifying information?
What are segments?