Interested to Buy Any Domain ? << Click Here >> for more details...
Identify the 2 commands to copy a configuration from a TFTP
server
to RAM?
A.) configure network
B.) configure overwrite
C.) copy backup-config running-config
D.) copy tftp running-config
- 1 Answers
- 4389 Views
- I also Faced
- E-Mail Answers
When using access lists, it is important where those access lists are placed. Which statement best describes access list placement? A. Put standard access lists as near the destination as possible. Put extended access lists as close to the source as possible. B. Put extended access lists as near the destination as possible. Put standard access lists as close to the source as possible. C. It isn't import where access lists are placed since the router will read and cache the whole list. D. Put access lists as close to corporate headquarters as possible.
Which command specifies a second subinterface on serial interface 0? A. interface s 0.2 point-to-point B. interface 2 s.0 point-to-point C. suberinterface 2.s 0 point-to-point D. interface s 0 sub 2 point-to-point E. interface s 0.1 point-to-point sub 2
Can you explain different components in PKI?
what does PPTP use for encryption and authentication?
On Cisco catalyst 5000 how would you set the second port on the controller in the first slot to full duplex? A.) Set port duplex 1/1 full B.) Set port duplex 1/2 full C.) Set port duplex 0/1 full D.) Set port duplex 0/2 full
Identify the command to configure the router to boot from an alternate IOS located in flash? A.) boot system flash IOS.exe B.) boot system tftp IOS.exe 172.16.5.1 C.) boot system alternate IOS.exe D.) boot system rom IOS.exe
What type of frame does CDP use to gather information about it's neighbors? A.) TCP/IP B.) Novell-ether C.) Subnetwork Access Protocol (SNAP) D.) Ethernet_II
Which company mange ip's?
hi i am facing one problem.ptoblem is like that i am getting output error on mine router ethernet interfae here is the cisco#show interface e0 Ethernet0 is up, line protocol is up Hardware is QUICC Ethernet, address is 0030.802d.2a17 (bia 0030.802d.2a17) Internet address is 202.122.20.225/28 MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec) ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:00, output 00:00:00, output hang never Last clearing of "show interface" counters 05:55:07 Queueing strategy: fifo Output queue 0/40, 0 drops; input queue 0/75, 0 drops 5 minute input rate 10000 bits/sec, 11 packets/sec 5 minute output rate 29000 bits/sec, 11 packets/sec 1515202 packets input, 359100396 bytes, 1 no buffer Received 6 broadcasts, 0 runts, 0 giants, 1 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 0 input packets with dribble condition detected 1584394 packets output, 1623395338 bytes, 0 underruns 1820 output errors, 26732 collisions, 0 interface resets 0 babbles, 0 late collision, 9698 deferred 18 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out output cisco# what is the reason how to solve this please tell me i am using cisco asa 5520 behid mine internet router and no error on the asa inside interface
Hi all, Sorry, but i want to say that right now i have around two years experience and doing the job as a network engineer(ccna certified).but i want switch job so please can tell me any opportunity.
Which command assigns the login password CISCO on the console terminal line? A. line vty 0 login password cisco B. line console login password cisco C. line login terminal password cisco D. line console 0 login E. line console 0 login password cisco
There is a process in Frame-Relay where LMI resolves an IP address from a DLCI number. What is this called? A.) arp B.) inverse arp C.) rarp D.) automap E.) reverse arp F.) arp
CCNA 
