Interested to Buy Any Domain ? << Click Here >> for more details...
Identify the command to determine if CDP is enabled? A.) show enable cdp B.) show cdp enabled C.) show cdp run D.) show cdp
1 3782Which 2 commands shows the Cisco IOS filename? A.) show IOS B.) show ver C.) show flash D.) show mem E.) show NVRAM
1 4479Identify the command to copy a configuration file from a TFTP server to a routers active configuration? A.) Router# copy running-config tftp B.) Router# copy tftp running-config C.) Router# copy tftp 172.16.0.1 running-config D.) Router(config)# copy tftp running-config
1 4942Identify the command mode necessary to enter the extended ping command? A.) Router# B.) Router> C.) Router(config)# D.) Router(ext-ping)#
1 4998Identify the command to configure the router for IGRP autonomous system 100? A.) Router(config)# router igrp 100 B.) Router> router igrp 100 C.) Router# router igrp 100 D.) Router(config)# router igrp
CMS,
3 7280Identify the command that forces the router to load into ROM mode upon a reload? A.) boot system rom B.) rom boot C.) boot system flash rom D.) boot router rom
1 4494Identify the command that specifies Serial 0 in slot 1? A.) Router(config)# interface serial1/1 B.) Router(config)# interface serial1/0 C.) Router(config)# interface serial0.1 D.) Router(config)# interface serial0/1
1 5243Identify the command to configure the configuration-register? A.) Router# config-register 0x2102 B.) Router(config)# config-register 0x2102 C.) Router(config-reg)# 0x2102 D.) Router> config-register 0x2102
1 4242Identify the command to disable CDP on an interface? A.) Router(config-if)# no cdp enable B.) Router(config-if)# no cdp run C.) Router# no cdp enable D.) Router(config-if)# no cdp
1 5710Identify the command that will display the RIP routes entering and leaving the router? A.) Router(config)# debug ip rip B.) Router# debug ip rip C.) Router>debug ip rip D.) Router# debug rip routes
ABC,
1 3921Identify the prompt displayed if in privileged exec mode? A.) Router(config)# B.) Router# C.) Router> D.) Router(priv)#
2 7632'Show cdp neighbors detail' show the following 3 pieces of information? A.) Hardware platform B.) Software version C.) Same as 'show version' command D.) Up to 1 address for each protocol E.) Non-direct connected routers
2 7039Identify the command mode necessary to enter the standard ping command? A.) Router(config)# B.) Router> C.) Router(std-ping)# D.) Router(config-if)#
2 5961Identify the command to run 'setup'? A.) Router(config)#setup B.) Router?setup C.) Router#setup D.) Router>setup
1 5532Identify the command that configures serial0 for PPP encapsulation? A.) Router(config)# encapsulation ppp B.) Router(config-if)# encapsulation serial ppp C.) Router(config-if)# encapsulation ppp D.) Router# encapsulation ppp
2 6967
What are the different types of password used in securing a cisco router?
Explain why UDP is lease favored when compared to TCP?
What does protocol mean?
In IPSec what is SAD, SPD and SA's?
Explian what is a node?
Hi Jitendera, Wat do u do..?? I mean r u working anywhere???? Basically where r u from??? If u don't hv any problem, u can say..?? Or else mail me mr.shahin07@gmail.com
Given the configuration example: interface ethernet0 ipx network 4a ipx access-group 800 out interface ethernet1 ipx network 3d interface ethernet2 ipx network tc access-list 800 permit 3d 4a Which action result from implementing this configuration? a-Traffic from network 3d for network 4a will be forwarded out e0 b-IPX network 5c will not receive any traffic c-Traffic from network 3d, destined for network 4a, will be forwarded out e2 d-Traffic from network 3d for network 3d will be forwarded out e0
What is the minimum request timer?
On which base distance vector choose best path?
Tell me how many fillers we can put in one ip of ipv6?
How many reserve ports?
Do we subletting of ip?
What port does rip use?
1350 Value in which type of access-list?
Can you explain voluntary and compulsory tunnels?
