Interested to Buy Any Domain ? << Click Here >> for more details...
Identify the 2 commands that display the clock rate
configured on
the serial0 interface?
A.) show serial0
B.) show interface serial0
C.) show clock rate serial 0
D.) show controllers serial 0
E.) show running-config
- 5 Answers
- 9870 Views
- I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / ajay dalvi
answer is D and E show controllers will display the DCE end
| Is This Answer Correct ? | 2 Yes | 0 No |
Answer / guest
B is incorrect for 2 reasons- firstly the command is show
interfaces...not interface, and secondly it does not give
info on the clockrate.
D and E are the correct answers that list clockrate within
the outputs.
| Is This Answer Correct ? | 1 Yes | 0 No |
Answer / jerome
First answer is sure B.
the second is a little more complicated.
If the serial interface 0 is DCE, the answer is E because we
have to specify a cloak rate but nothing is written in the
question about that...
If your serial interface is really named serial 0 ( not
serial 0/0 or serial 0/0/0 as the newest routers)the answer
is D.
You will be able to see if your interface is DTE or DCE and
the clock rate used.
( Example :
Cable type : V.35 DTE cable, received clockrate 56000 )
| Is This Answer Correct ? | 1 Yes | 4 No |
What parameter is used with statically assigned routers to tell packets which interface to use to reach a distant network? A.) Mask B.) Subnet C.) Default gateway D.) Interface
Which is true regarding half duplex Ethernet operation? A.) Half Duplex ethernet technology provides a transmit circuit connection wired directly to the receiver circuit at the other end B.) Half duplex transmission between stations is achieved by using point to multipoint Ethernet and Fast Ethernet C.) With Half Duplex transmission logically circuits feed into a single cable creating a situation similar to a one way bridge D.) Half Duplex transmission between stations is achieved using Point to Point Ethernet & Fast Ethernet
Identify the command to configure a description on an interface? A.) Router> description Finance department B.) Router(config)# description Finance department C.) Router(config-if)# description Finance department D.) Router# description Finance department
Cisco routers use wildcard masking to identify how to check or ignore corresponding IP address bits. What does setting a wildcard mask bit to 0 cause the router to do? A. It tells the router to check the corresponding bit value. B. It tells the router to ignore the corresponding bit value. C. It tells the router to check its alternate routing list. D. It tells the router to use its primary routing list.
What would be the proper wildcard mask to permit all odd numbered hosts on the 10.48.0.0/12 network? access-list 1 permit 10.48.0.0 0.15.255.255 access-list 1 permit 10.48.0.1 0.15.255.254 access-list 1 permit 10.48.0.0 0.15.255.1 access-list 1 permit 10.48.0.0 0.0.0.254 access-list 1 permit 10.48.0.0 0.0.0.255
UDP works at which layer of the DOD model? A.) Internet B.) Host-to-Host C.) Transport D.) Data Link
Identify the components in the following command 'interface serial0/1/1' A.) Serial interface, port number 0, slot 1, port adapter 1 B.) Serial interface, slot 1, port number 1, port adapter 0 C.) Serial interface, slot 0, port adapter 1, port number 1
If bandwidth will increase what will happen?
Do you found the Cisco Certification 642-067 exam Guide ?
The Internet Protocol (IP) occurs at what layer of the seven layer model? A.) Physical B.) Presentation C.) Network D.) Datalink E.) Session F.) Transport
You have OSPF traffic flooding your network via one of your router interfaces. Write the access list line that will deny all ospf traffic. Don't worry about the other lines of the access list.
In order to limit the quantity of numbers that a system administrator has to enter, Cisco can use which abbreviation to indicate 0.0.0.0? A. host B. any C. all D. include
CCNA 
