Interview Questions Answers in Electrical Engineering

deepak tardalkar

{ City } ahmedabad
< Country > india
* Profession * engineer
User No # 30824

Total Questions Posted # 17
Total Answers Posted # 4

Total Answers Posted for My Questions # 48
Total Views for My Questions # 247069

Users Marked my Answers as Correct # 57
Users Marked my Answers as Wrong # 30

Questions / { deepak tardalkar }

Questions Answers Category Views Company eMail

why generator and t/f ratings given in kva & motor rating is in KW?

6 Electrical Engineering 13138

In 400KV Switchyard, we have used Circuit Breaker With PIR, what is the significance of PIR & why they'r used?

2 Electrical Engineering 20593

Why the size of transformer decreases if we increases the frequency?

Graphics Engineering,

5 Electrical Engineering 36628

What is the diffrence (Technical & Construction ) between CBCT & Normal CT?

Electrical Engineering 2039

Why the cost of CT increases with the decreasing of its CT Ratio (Technical Reason)?

Vedanta,

2 Electrical Engineering 6276

How the size of transformer decreases if we increases the frequency?

2 Electrical Engineering 5402

How to decide the rating of CBCT? We have 6.6Kv switchgear & having 50/1 cbct ,i want to know how this 50/1 A came? On what basis we decide CBCT reting?

Cross,

1 Electrical Engineering 8772

What is the effect of solar radiation on the design of an Isolated Phase Busduct?

Exide, Punj Lloyd Ltd,

Electrical Engineering 2368

What is the diffrence between PS & metering CT (5p20,0.5 etc.)? Why in PS class CT only Vk is given ? Is PS class CT is more accurate than metering CT?

1 Electrical Engineering 4822

What is milivolt dop test in Busducts? What is its significance & procedure to do the test?

Electrical Engineering 2102

How to calculate cable size for a particular load? i have 12 MW,11KV Motor 3 Phase, what should be cablesize? What are the points to remember for cable sizing calculations?

2 Electrical Engineering 6723

I have seen 1 video in which a person getting shock while standing at top of a train,i have 1 question? why the people sitting in the train doesn't get shock while that man getting shock from top of the train? How the earthing of train works?

Bhel,

17 Electrical Engineering 22681

How to take vector group test of a transformer? Suppose we dont know the vector group of transformer, how to check its vector group through test? I have 3 transformer DYn11 & DYno& Ynd11, how to confirm its vector group?

1 Electrical Engineering 5688

Why tripping not occur when the transmission breaks? Doesn't we provide earthfault protection for it?

1 Electrical Engineering 3433

Why tripping not occur when the transmission lines (11KV & above) breaks? Doesn't we provide earthfault protection for it?

1 Electrical Engineering 5266

[1] 2 Next

Answers / { deepak tardalkar }

Question { BARC, 22704 }

What is the operating range(tolerance) of voltage and
frequency of grid supply in india?

Answer

For Voltage, it is +/- 10% &
For Frequence +/- 5%

Is This Answer Correct ?

37 Yes

25 No

Question { 8276 }

How can be decreased the size of transformer?

Answer

By increasing the frquency, we can reduce the size of
transformer (In air craft,size of tranformer are very small
as there frequncy is 400Hz)

Is This Answer Correct ?

3 Yes

2 No

Question { 16592 }

WHAT IS THE REASON FOR THE GROUND PIN IS BIGGER IN SIZE
COMPARING TO OTHER PINS?

Answer

As R is inversly proportional to area so as area increases
R decreases & in case of fault, it provided low resistant
path for fault current.

Is This Answer Correct ?

5 Yes

0 No

Question { 5984 }

how can we check the earth resistance

Answer

By earth resistance tester that consist of 2 electrodes
along with its leads.Connect one lead from earthpit to
tester & burry 2 electrodes in earth & connect there
respective lead with tester & then check the earth R. It
should be from 0 to 1 Ohm.

Is This Answer Correct ?

12 Yes

3 No