Interested to Buy Any Domain ? << Click Here >> for more details...
How to stop if Solaris system it rebooting continually.
What is the steps to come normal position.
- 8 Answers
- 15330 Views
- I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / abid
1. Go to ok> prompt by using stop+a keys
2. Boot in single user mode i.e., ok> boot -s
3. check the /etc/inittab file and make sure you can see
the number 3 is entered before default.
4. Once you make the changes reboot the system it should
work
| Is This Answer Correct ? | 13 Yes | 0 No |
Answer / kiranraj
There might be some hardware issue, Go to the editor mode
or sc and do a break or port break respectively....the
server should come to ok prompt..check for errors in the
logs..ie; showlogs at sc if you find any error report it to
sun eng..or run diagnostic and find the fault hardware and
replace it...(usually the issue would be with one of the
cpu/dimm or the system board)
| Is This Answer Correct ? | 3 Yes | 1 No |
Answer / sfrahman
Solaris server rebooting has many different stages...
Even the inittab file is also seem perfect then the problem
may be with the file system or mounting point so check.
Some times all are correct when the server reach GUI mode it
get restart.
check dtlogin and gdm setup.....
| Is This Answer Correct ? | 2 Yes | 0 No |
Answer / j.srinivasa rao
I faced the same problem in few days back,found that
processor cooling fan is not working properly some times
the cooling fan is not running properly so by that time
whatever the heat generated from the processor is not going
out of the cpu,so more heat generated and it is strucks in
inside the cabinet,finally what iam telling is pls replace
the processor cooling fan this is one of the reason not all
the time.
Regards
srinivasa rao.J
| Is This Answer Correct ? | 2 Yes | 1 No |
I AM not sure.
but it will work in linux.
check
# vi /rc/rc.local
if any line type "init 6 ".
then remove "init 6"
| Is This Answer Correct ? | 0 Yes | 0 No |
Answer / prakash
check schedule for anyone user was post at job, check at job
| Is This Answer Correct ? | 0 Yes | 1 No |
Answer / nn
There might be some problem is hardware ..need to chek the
cables connected to the server specifically power cable....
still problem persist ...need to chek the physical RAM on
the server.once remove it and clean properly and place it
on the same position.else need to chage the RAM.
| Is This Answer Correct ? | 5 Yes | 7 No |
1. How do you replace a failed boot disk under meta in solaris? Step by step explanation? 2. How do you remove meta only for the root slice? remaining slices should run under meta? 3. what you would do if you want to replace a slice using metareplace option? 4. what is the significance of 51% state database replicas in SVM? 5. what are the common errors you find in Solaris Volume manager? 6. You have a boot disk under svm, the machine fails to boot and remains in ok prompt? what could be the possible reason? 7. metastat -p shows a metavolume needs replacement. Metavolume is a single way mirror only. Actually you find disk and metavolumes are ok and I/O is happening to the filesystems… how will you remove the metareplace message that comes out of metastat. 8. How to create a shared disk group in VxVM? 9. What is the difference between private and public regions in Veritas Volume manager? 10. what would you do if the private region of a particular disk group is full? What are the design considerations for the size of private region in Vxvm disk group? 11. How to replace a corrupt private region? in vxvm 3.5 and greater versions… 12. How would you convert a volume from gen to fsgen? why should you do that? 13. How can you unencapsulate a boot disk in VxVM? 14. How to identify multiple paths for a disk. 15. What is the difference between Vxdmp and EMC powerpath? 16. vxdisk -o alldgs list o/p shows some disk groups in braces… What does that signify? 17. what are the various layouts that are available in VxVM? 18.What is a layered volume? how to create it using vxmake? 19.How to quickly mirror a volume, if the volume is empty? 20. How to grow a volume? 21. What is the difference between failing and failed disks? 22. How to replace a failed disk in Veritas? 23. Plex is in a disabled state. How will you recover? what are the steps to follow? 24.what is the difference between detached and disassociate state of plexes? 25. Whats the boot process of VxVM? 26. Whats the difference between SVM and VxVM? What would you recommend to your clients? why? 27.What are the various clusters you have worked on? 28. Which cluster is better VCS or Sun cluster? 29. Compare and contrast VCS and Sun Cluster. 30.how will you start VCS service? What are the configuration files in VCS? 31. How would switch a service group? 32. How would you freeze a service group? 33. What is a Split brain scenario ?
I have a "telnet" error then what you will do?
how to change boot disk
Explain setuid, setgid and stickybit
How to view the kernel (shmmax)paramiter value in solaris 10?
What is the difference between dsk and rdsk
How to configure mirror with hot spare in vxvm I know how to create mirror with vxassist: #vxassist -g <diskgroup name> make <volume name> <vol size> layout=mirror I know how to create hot spare with vxedit #vxedit -g <diskgroup name> set spare=on diskname but i don't how to attach hot spare to mirror? can some one plz help in this issue.. Thanks & Regards, SaiKrishna. kanuparthi_sai@yahoo.com my alternate E-Mail id: ksaikrishna7@gmail.com
how to view how many samba user in solaris
How to add a new LUN in exit disksets (metasets) in solaris please answer me step by step procedure?
1)How to identify VXVM version? 2)What the path of scconf in cluster?
When you "ping server" and "ping server.domainname", you get different results. Why?
what is cluster.
Solaris Commands 
