Answer / sateesh.mamilla

rip igrp eigrp ospf

hello none none 6osec 10secs

update 30sec 90sec triggerd 30mins+
timers +triggered triggered


dead 180 3*hello 3*hello 4*hello
timers secs

When setting up a frame-relay network between a Cisco router and a non-Cisco router, what encapsulation type should you use? A.) SAP B.) CISCO C.) IANA D.) Apollo E.) IETF F.) Q933A

2 Answers  

---

Which command would show all Ethernet interfaces with IPX configured on them? A.) show interface ipx ethernet B.) show ipx interface C.) show ipx interface ethernet D.) show ipx E.) show version F.) show run

1 Answers  

---

take a pen and copy before solving that question there is a router name Ra there is two switch sw1 and sw2 sw1 is coneceted through fa0/1 interface of router Ra sw2 is conected through the fa1/1 serai interface of router s0/1 conected through the isp with it ip address 192.168.1.1 now therer are three host conexted through the sw1 and having ip host1=10.1.2.1 host2=10.1.2.2 host3=10.1.2.3 now there is also 3ree host conected through switch 2 i.e sw2 having ip host4=10.1.1.1 host 5=10.1.1.2 host 6=10.1.1.3 now i think u have made corect confrigation.now questios is started network admin configure the Ra router in that fassion Ra(config)#access-list 2 permit 10.1.1.0 0.0.0.255 Ra(config)#line vty 0 4 ra(config)#access-class 2 in now question is that why should network admnistratoe do it in this maneer A to give access sw1 host to acess internet B to prevent sw1 host from acessing comand promt c to prevent sw2 host from accessing console of router ra D to give sw2 host access to the enternet e prevent sw1 host from accessing internet f to prevent sw1 host from acessing the sw2 host network isp------(s0/1)..RA..(fa1/1)---SW2-host (4,5,6) | | (sw1)------host 1,2,3 this is not exect digarm but help to derive the diagram plz answer as soon as possible

6 Answers   AT&T,

---

Identify the protocol to test connectivity without configuring any layer 3 protocols? A.) TCP B.) Ping C.) IP D.) CDP E.) Telnet

1 Answers  

---

Assume that you are editing a line of text on a Cisco router. What key-stroke combination would take you to the beginning of the line? A.) CTRL-B B.) CTRL-Z C.) CTRL- D.) CTRL-A E.) CTRL- F.) CTRL-

2 Answers  

---

Select the compression protocols for PPP? A. Stac B. Predictor C. Quality D. Magic Number

1 Answers  

---

Which OSI Reference Layer controls application to application communication? A.) Datalink B.) Network C.) Transport D.) Session E.) Physical

2 Answers  

---

What is ‘round-trip time’?

0 Answers  

---

Which 3 statements describe default encapsulation and LMI type configuration? A.) There are only four encapsulations and 3 LMI type options B.) The LMI type config term options C.) In release 11.3 the LMI type is autosensed D.) The default LMI is Cisco E.) IETF encap must be configured unless the connecting routers are both cisco

1 Answers  

---

Request any body to explain the parameters of Ipsec vpn tunnel while creating a tunnel in Cisco ASA.

3 Answers   HCL,

---

What is the terminal emulation?

0 Answers  

---

In stead of 0.0.0.0 wild card mask what you can write after ip?

0 Answers  

---