What parameter is used with statically assigned routers to tell

packets which interface to use to reach a distant network?

A.) Mask

B.) Subnet

C.) Default gateway

D.) Interface



What parameter is used with statically assigned routers to tell packets which interface to use to..

Answer / guest

Answer: D

The interface parameter tell a packet which interface to use
to reach

other networks.

Is This Answer Correct ?    0 Yes 0 No

Post New Answer

More CCNA Interview Questions

Which of the following is a routing protocols? TCP RIP SMTP UDP

7 Answers  


the situation iz like ths -at a specific time in our company the internet connectivity goes off...v hav two networks in our company...but out of it only one link goes down for 5-10 sec...a fastethernet port becomes down for few sec and automatically becomes Up... Is this occures becoz of Power?? If yes thn y the 2nd network is not affected??

2 Answers   SoftTech,


Identify the components in the following command 'interface serial0/1/1' A.) Serial interface, port number 0, slot 1, port adapter 1 B.) Serial interface, slot 1, port number 1, port adapter 0 C.) Serial interface, slot 0, port adapter 1, port number 1

1 Answers  


What is a back off on an 802.3 networks? A. It is latency in store and forward switching B. It is the time used for token passing from machine to machine C. It is the retransmission delay that is enforced when a collision occurs D. It is the result of two nodes transmitting at the same time. The frames from each transmitting device collide and are damaged

1 Answers  


The -- terminal no editing -- command will perform what function? A.) Edit the contents of NVRAM B.) Allows access to the terminal port C.) Stops the advanced editing feature D.) Enable password functions

2 Answers  






hi... i am usin packet tracer 5.0.. i hav connect two routers A and B. A has 200.100.25.100 and 1.0.0.1 and router B has 200.100.50.100 and 1.0.0.2... i hav connected 1.0.0.1 and 1.0.0.2... now i want to route 200.100.25.100 and 200.10.50.100 usin rip.. i enable rip in both the routers... but whn i give the command show ip route... i jus get this Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set A# so can sombody tell me where i hav gone wrong... thanku

1 Answers  


what is used for passive intercae comand mine answer-to prevent to take update from outside

2 Answers  


What is the maximum number of subnets that can be assigned to networks when using the address 172.16.0.0 with a subnet mask of 255.255.240.0? (Assume older version UNIX workstations are in use.) A. 16 B. 32 C. 30 D. 14 E. It is an invalid subnet mask for the Network.

2 Answers  


Define osi?

0 Answers  


Which of the following are characteristics of UDP? A.) UDP is connection oriented. B.) UDP is used with TFTP. C.) UDP is unreliable. D.) UDP is connectionless. E.) UDP is at the transport layer. F.) UDP uses no acknowledgements.

6 Answers  


Identify the command that configures the bandwidth to 56K? A.) Router(config-if)# bandwidth 56000 B.) Router(config-if)# bandwidth 56k C.) Router(config)# bandwidth 56 D.) Router(config-if)# bandwidth 56

1 Answers  


Why OSI layers having 7 layers instead of one layer.

8 Answers   HCL,


Categories