take a pen and copy before solving that question there is a router name Ra there is two switch sw1 and sw2 sw1 is coneceted through fa0/1 interface of router Ra sw2 is conected through the fa1/1 serai interface of router s0/1 conected through the isp with it ip address 192.168.1.1 now therer are three host conexted through the sw1 and having ip host1=10.1.2.1 host2=10.1.2.2 host3=10.1.2.3 now there is also 3ree host conected through switch 2 i.e sw2 having ip host4=10.1.1.1 host 5=10.1.1.2 host 6=10.1.1.3 now i think u have made corect confrigation.now questios is started network admin configure the Ra router in that fassion Ra(config)#access-list 2 permit 10.1.1.0 0.0.0.255 Ra(config)#line vty 0 4 ra(config)#access-class 2 in now question is that why should network admnistratoe do it in this maneer A to give access sw1 host to acess internet B to prevent sw1 host from acessing comand promt c to prevent sw2 host from accessing console of router ra D to give sw2 host access to the enternet e prevent sw1 host from accessing internet f to prevent sw1 host from acessing the sw2 host network isp------(s0/1)..RA..(fa1/1)---SW2-host (4,5,6) | | (sw1)------host 1,2,3 this is not exect digarm but help to derive the diagram plz answer as soon as possible

6 Answers   AT&T,

---

what is standard and extended acess list? what are the commands for extended and acess list?

3 Answers   HCL,

---

Which protocol is used for booting diskless workstations? A.) IP B.) ARP C.) RARP D.) TCP E.) SNMP

2 Answers  

---

Which device works at the Network Layer of the OSI model? Router Switch Bridge Hub

5 Answers   CET, IBM,

---

How does a switch use store and forward? A.) By using a Class I repeater in a collision domain B.) The LAN switch copies the entire frame into its onboard buffers and then looks up the destination address in its forwarding, or switching, table and determines the outgoing interface C.) By using broadcast addresses as source addresses D.) The switch waits only for the header to be received before it checks the destination address and starts forwarding the packets

1 Answers  

---

If a router uses static routing, how does it learn the route to remote networks? The router uses a RIP request to obtain remote network numbers. The router uses a routing protocol to exchange remote network numbers. The router uses DNS request packets to obtain remote network numbers. The Network Administrator manually configures the remote networks.

1 Answers  

---

What is the maximum number of subnets that can be assigned to networks when using the address 172.16.0.0 with a subnet mask of 255.255.240.0? (Assume older version UNIX workstations are in use.) A. 16 B. 32 C. 30 D. 14 E. It is an invalid subnet mask for the Network.

2 Answers  

---

How does rip differs from igrp?

0 Answers  

---

Which of the following protocols are used for logical network addressing? A.) IP B.) TCP C.) ARP D.) ICMP E.) RARP F.) BootP

5 Answers  

---

Identify the purpose of the Trace command? A.) Explorer packet transmitting routing information B.) Test connectivity C.) Determine the path a packet is taking through the network D.) Transmits user data when buffers are full

1 Answers  

---

What's the default CDP holdtime in seconds for Cisco routers? A.) 30 seconds B.) 180 seconds C.) 90 seconds D.) 60 seconds

4 Answers  

---

Identify the command to display the IP routing table? A.) show route B.) show ip route C.) show ip table route D.) show ipx route

1 Answers  

---