Answer / akhilesh

It is system which include hardware and software both and
Software is used to make the hardware working for specific
purpose.

Answer / ganesh

Embedded system means make any hardware compatible through
different software.Also a combination of 2 or more s/w + h/w
is called Emb.sys.

Answer / dhineshkumar

*the system which contains micro controller is called
embedded sysyem.
*In the embedded system the software is mounted on hardware

Answer / manoj

An embedded system is any electronic system that uses a CPU chip, but that is not a general-purpose workstation, desktop or laptop computer.
An embedded system is a special-purpose computer system designed to perform a dedicated function. Unlike a general-purpose computer, such as a personal computer, an embedded system performs one or a few pre-defined tasks, usually with very specific requirements, and often includes task-specific hardware and mechanical parts not usually found in a general-purpose computer.

Read more: http://romux-loc.com/tutorials/embedded-system#ixzz30vyGP3r8

Answer / vignesh

pruthvi is right only to a certain extent.

In short, Embedded System gives intelligence to machines.
Machines may be either electrical or electronic or
mechanical or a combination of all.

Answer / anantharaja

Electronic devices that incorporate a computer(usually
micro controller)within their implementation.

Answer / akhil

it is system of linking both h\w&s\w

Answer / manish

Embedded system is the system to perform one and only one
task.for e.g. computer is not embedded system but if we
consider mouse having only one functionality is an example
of embedded

Answer / manikanda prabhu.p

Embedded system is a combination of hardware and software

Answer / essa suresh

embedded system is some combination of computer hardware and
software, either fixed in capability or programmable, that
is specifically designed.

Where can we find the sample assembly language programs?

0 Answers  

What does eu do?

0 Answers  

When is the LOCK prefix used often?

0 Answers   CDAC,

I have code and test bench however it is not working porperly. Need help to get it working. module fsm(clock,reset,coin,vend,state,change); \\these are the inputs and the outputs. input clock; input reset; input [2:0]coin; output vend; output [2:0]state; output [2:0]change; \\i need to define the registers as change,coin and vend reg vend; reg [2:0]change; wire [2:0]coin; \\my coins are declared as parameters to make reading better. parameter [2:0]NICKEL=3’b001; parameter [2:0]DIME=3’b010; parameter [2:0]NICKEL_DIME=3’b011; parameter [2:0]DIME_DIME=3’b100; parameter [2:0]QUARTER=3’b101; \\MY STATES ARE ALSO PARAMETERS . I DONT WANT TO MAKE YOU READ \\IN MACHINE LANGUAGE parameter [2:0]IDLE=3’b000; parameter [2:0]FIVE=3’b001; parameter [2:0]TEN=3’b010; parameter [2:0]FIFTEEN=3’b011; parameter [2:0]TWENTY=3’b100; parameter [2:0]TWENTYFIVE=3’b101; \\AS ALWAYS THE STATES ARE DEFINED AS REG reg [2:0]state,next_state; \\MY MACHINE WORKS ON STATE AND COIN always @(state or coin) begin next_state=0; \\VERYFIRST NEXT STATE IS GIVEN ZERO case(state) IDLE: case(coin) \\THIS IS THE IDLE STATE NICKEL: next_state=FIVE; DIME: next_state=TEN; QUARTER: next_state=TWENTYFIVE; default: next_state=IDLE; endcase FIVE: case(coin) \\THIS IS THE SECOND STATE NICKEL: next_state=TEN; DIME: next_state=FIFTEEN; QUARTER: next_state=TWENTYFIVE; //change=NICKEL default: next_state=FIVE; endcase TEN: case(coin) \\THIS IS THE THIRD STATE NICKEL: next_state=FIFTEEN; DIME: next_state=TWENTY; QUARTER: next_state=TWENTYFIVE; //change=DIME default: next_state=TEN; endcase FIFTEEN: case(coin) \\THIS IS THE FOURTH STATE NICKEL: next_state=TWENTY; DIME: next_state=TWENTYFIVE; QUARTER: next_state=TWENTYFIVE; //change==NICKEL_DIME default: next_state=FIFTEEN; endcase TWENTY: case(coin) \\THIS IS THE FIFTH STATE NICKEL: next_state=TWENTYFIVE; DIME: next_state=TWENTYFIVE; //change=NICKEL QUARTER: next_state=TWENTYFIVE; //change==DIME_DIME default: next_state=TWENTY; endcase TWENTYFIVE: next_state=IDLE; \\THE NEXT STATE HERE IS THE RESET default : next_state=IDLE; endcase end always @(clock) begin \\WHENEVER I GIVE A RESET I HAVE TO MAKE THE STATE TO IDLE AND VEND TO 1 if(reset) begin state <= IDLE; vend <= 1’b0; // change <= 3’b000; end \\THE CHANGE ALSO HAS TO BECOME NONE else state <= next_state; case (state) \\HERE WE DECIDE THE NEXT STATE \\ALL THE STATES ARE DEFINED HERE AND THE OUTPUT IS ALSO GIVEN IDLE: begin vend <= 1’b0; change <=3’d0; end FIVE: begin vend <= 1’b0; if (coin==QUARTER) change <=NICKEL; else change <=3’d0; TEN: begin vend <= 1’b0; if (coin==QUARTER) change <=DIME; else change <= 3’d0; FIFTEEN : begin vend <= 1’b0; if (coin==QUARTER) change <=NICKEL_DIME; else change TWENTY : begin vend <= 1’b0; if (coin==DIME) change <=NICKEL; else if (coin==QUARTER) TWENTYFIVE : begin vend <= 1’b1; change <=3’d0; end default: state <= IDLE; endcase end endmodule module test; \\THE INPUT IN THE FSM MODULE ARE REG HERE reg clock,reset; reg [2:0]coin; \\THE OUTPUT IN THE FSM MODULE ARE WIRES HERE wire vend; wire [2:0]state; wire [2:0]change; \\THE PARAMETERS AGAIN FOR THE COIN AND STATE parameter [2:0]IDLE=3’b000; parameter [2:0]FIVE=3’b001; parameter [2:0]TEN=3’b010; parameter [2:0]FIFTEEN=3’b011; parameter [2:0]TWENTY=3’b100; parameter [2:0]TWENTYFIVE=3’b101; parameter [2:0]NICKEL=3’b001; parameter [2:0]DIME=3’b010; parameter [2:0]NICKEL_DIME=3’b011; parameter [2:0]DIME_DIME=3’b100; parameter [2:0]QUARTER=3’b101; \\I MONITOR THE TIME,DRINK,RESET,CLOCK,STATE AND CHANGE FOR CHANGES. initial begin $display("Time\tcoin\tdrink\treset\tclock\tstate\tchange"); $monitor("%g\t%b\t%b\t%b\t%b\t%d\t% d",$time,coin,vend,reset,clock,state,change); \\NEW FEATURE: MY MACHINE HAS THE FACILITY TO DUMP VARIABLES SO THAT \\ I CAN VIEW THEM USING A VCD VIEWER. $dumpvars; $dumpfile("file.vcd"); // Dump output file. \\THIS IS WHERE THE COINS ARE ADDED. clock=0; reset=1; \\FIRST LETS RESET THE MACHINE #2 reset=0; coin=NICKEL; \\CHECK FOR STATE 1 #2 reset=1; coin=2’b00; #2 reset=0; coin=DIME; \\RESET AGAIN AND CHECK FOR STATE 2 #2 reset=1; coin=2’b00; #2 reset=0; \\RESET AGAIN AND CHECK FOR STATE 5 coin=QUARTER; #2 reset=1; coin=2’b00; #2 reset=0; \\RESET AGAIN AND CHECK FOR STATE 5 coin=NICKEL; #2 coin=NICKEL; #2 coin=NICKEL; #2 coin=NICKEL; #2 coin=NICKEL; #2 reset=1; coin=2’b00; #2 reset=0; \\RESET AGAIN AND CHECK FOR STATE 5 AND SO ON coin=NICKEL; #2 coin=DIME; #2 coin=DIME; #2 reset=1; coin=2’b00; #2 reset=0; coin=NICKEL; #2 coin=DIME; #2 coin=QUARTER; #2 reset=1; coin=2’b00; #2 reset=0; coin=NICKEL; #2 coin=NICKEL; #2 coin=NICKEL; #2 coin=DIME; #2 reset=1; coin=2’b00; #2 reset=0; coin=NICKEL; #2 coin=NICKEL; #2 coin=NICKEL; #2 coin=NICKEL; #2 coin=DIME; #2 reset=1; coin=2’b00; #2 reset=0; coin=NICKEL; #2 coin=NICKEL; #2 coin=QUARTER; #2 reset=1; coin=2’b00; #2 reset=0; coin=NICKEL; #2 coin=QUARTER; #2 reset=1; coin=2’b00; #2 $finish; end \\THE CLOCK NEEDS TO TICK EVERY 2 TIME UNIT always #1 clock=~clock; //always @(state) // coin=!coin; initial begin if (reset) coin=2’b00; end \\THIS IS WHERE I INSTANTIATE THE MACHINE fsm inst1(clock,reset,coin,vend,state,change); endmodule

0 Answers   Intel,

Define the jobs performed by the biu and eu in the 8086.

0 Answers  

In which T-state does the CPU sends the address o memory or I/O and the ALE signal for Demultiplexing

0 Answers   CDAC,

What is the main difference between 8085 and 8086 processors?

0 Answers  

Which is the stack used in 8085?

0 Answers  

What is the function of eu?

0 Answers  

What are the different flags in 8085?

24 Answers   Spectra Innovations, TCS, Wipro,

How to control and timing circuitry of the 8085.

0 Answers  

Explain sim and rim instructions?

0 Answers