Interested to Buy Any Domain ? << Click Here >> for more details...
Which statement about half duplex Ethernet operations is true?
A. With half duplex transmission frames feed into a single
cable in one direction at a time.
B. Half duplex transmission between stations is achieved by
using point to point Ethernet and Fast Ethernet connections
C. Half duplex transmission between stations is achieved by
using point to munificent Ethernet and Fast Ethernet connections
D. Half duplex Ethernet technology provides a transmit
circuit connection wired directly to the receiver circuit at
the other end of the connection
- 5 Answers
- 10729 Views
- I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / rohit dodia
A. With half duplex transmission frames feed into a single
cable in one direction at a time.
| Is This Answer Correct ? | 4 Yes | 1 No |
Answer / rohit dodia
A. With half duplex transmission frames feed into a single
cable in one direction at a time.
| Is This Answer Correct ? | 2 Yes | 2 No |
GUYS i was refraining the OLD post and i got a good Question and wana make sure that you guys Just did not vist it for answers if you are not Aware google it understand it and then answered it the question is -: Significance of IP helper-address Command on SW? Is it necessary to put this command? you donot wana to give answer please donot visit this question and increase the vistor name if you are thinking that answer is wrong mark it wrong and explain why you are marking it wrong
Identify the switching method that examines the destination MAC address as the frame is being received then begins forwarding the frame prior to receiving the entire frame? A.) Fragment-free B.) Store and Forward C.) Cut-through D.) Fast forward
Identify the following command to configure a secret password to 'cisco'? A.) Router(config)#enable password cisco secret B.) Router(config)#enable secret cisco C.) Router(config)#enable secret password cisco D.) Router(config)#set secret = cisco
What does the 'S' mean when looking at the routing table? A.) Statically connected B.) Directly connected C.) Dynamically attached D.) Shutdown route
The Physical layer works with which of the following: A.) Segments B.) Datagrams C.) Packets D.) Bits E.) Frames
The CSMA/CD Ethernet IEEE committee is defined as which of the following? A.) 802.2 B.) 802.3 C.) 802.4 D.) 802.5
Explain the difference between baseband and broadband transmission in ccna?
What is default cost of serial interface in ospf?
Which protocol resolves an IP address to a MAC address? A.) DHCP B.) RARP C.) ARP D.) NBP E.) DNS
Identify 3 characteristics of a MAC address? A.) Burned into the NIC B.) 48 bits long C.) Length is 32 bits D.) Used to identify a host device E.) Contains a network portion and a host portion
Hi Guys I am facing one problem while configuring PAP over Point to Point links. Configuration scenario is like this. ROUTER 1: (Hostname – R1) R1(config)#username R2 password CCNA2 R1(config)#interface serial 1/1 R1(config-if)ip address 10.0.0.1 255.0.0.0 R1(config-if)#lock rate 64000 R1(config-if)#encapsulation ppp R1(config-if)#ppp authentication pap R1(config-if)#ppp pap sent –username R1 password CCNA1 R1(config-if)#no shutdown ROUTER 2: (Hostname – R2) R2(config)#usename R1 password CCNA1 R2(config)#interface serial 1/1 R2(config-if)#ip address 10.0.0.2 255.0.0.0 R2(config-if)#encapsulation ppp R2(config-if)# ppp authentication pap R2(config-if)# ppp pap sent –username R2 password CCNA2 R2(config-if)#no shutdown Now problem is that, after configure the command “ppp authentication pap” the “Line protocol” status goes down on each router. But when I disable this command using “no ppp authentication pap”, the “Line Protocol” status goes up. What could be the problem, can anyone explain it plzzz….!!! Thanks in Advance…!! Shahin..
Which two statements about the store and forward switching method are true? (Choose two) A. Latency remains constant regardless of frame size. B. Latency through the switch varies with frame length. C. The switch receives the complete frame before forwarding it. D. The switch checks the destination address as soon as it receives the header and begins forwarding the fram immediately.
CCNA 
