Answer / guest

Answer: B

Answer / mukesh kumar

(B)

Identify the 2 commands that copies the configuration in NVRAM to RAM? A.) copy backup-config running-config B.) configure nvram C.) copy startup-config running-config D.) configure memory

3 Answers  

---

What are four benefits that can result from applying ISDN networking? (Choose four) A. Full time connectivity across the ISDN is spoofed by Cisco IOS routers using dial on demand routing (DDR) B. Small Once and Home Once sites can be economically supported with ISDN Basic Rate Interface (BRI) servkps C. ISDN replaces Signaling System 7 (SS7) in the Public Switched Telephone Network (PSTIC) backbone D. ISDN can be used as a backup service for a leased line connection between the remote and central chaps E. Modem racking and cabling can be eliminated by integration of digital modem cards on Cisco IOS Network Acess Servers (NAS)

2 Answers  

---

Identify 2 features of PPP PAP authentication? A.) Username and password is sent in clear text B.) Authentication messages are sent periodically during the connection C.) More secure than CHAP D.) Remote node is control of authentication process

1 Answers  

---

Which of the following statements is false? If your Frame Relay link does not support inverse ARP, you must manually map DLCIs to network Address. One of the major advantages of Frame Relay is its ability to connect to multiple PVCs using only one physical link. DLCI addresses are determined by the network administrator when installing the network. Which of the following statements is false? If your Frame Relay link does not support inverse ARP, you must manually map DLCIs to network Address. One of the major advantages of Frame Relay is its ability to connect to multiple PVCs using only one physical link. DLCI addresses are determined by the network administrator when installing the network. In order for two ends of virtual circuits to communicate using Frame Relay, their network addresses must be mapped to DLCIs.

2 Answers   Wipro,

---

Identify the purpose of the following command 'ip route 192.168.100.0 255.255.255.0 10.1.0.1' A.) Enabling a dynamic routing protocol B.) Creating a static route to the 10.1.0.0 network C.) Teaches the router about the distant network 192.168.100.0 and how it can be reached via 10.1.0.1 D.) Assigining the IP address 192.168.100.0 to an interface

2 Answers  

---

What do we check while configuring the server?

0 Answers  

---

here is your question sahin Hi Jitendera, If i m not wrong, then in EIGRP, Metric weight is set to K1(Bandwidth)=1, K2(Delay)=0, K3(Reliability)=1, K4(Load)=0, K5(MTU)=0. This is default setting for EIGRP. I knew about it from ICND 2 cisco press book. Three more questions - a) If we change the K value (I mean metric weight)on a router what will happen??? b) When redistribution is necessary in EIGRP. Is there any condition for that??? c) What is reference bandwidth for metric calculation in EIGRP. As we know, in OSPF, on a CISCO router reference bandwidth is 10Mbps.

3 Answers  

---

Which mode called privilege mode?

0 Answers  

---

Which command we give for see routing table?

0 Answers  

---

hi i have some difficulty plz reply as s0on as possible. 1 what is csma/cd(i know u are familer with that protocol) 2 what is the need for it and and 3 rd one in which i need help how to enable csma/cd at router or switches shain make it answer as sson as possibele and call me afetr reply thanks jitendera kuamr sinha

1 Answers  

---

WAN stands for which of the following? A.) Wide Arena Network B.) World Area Network C.) Wide Area News D.) Wide Area Network

1 Answers  

---

what is different between semi-managed and managed Switch ?

2 Answers  

---