Interested to Buy Any Domain ? << Click Here >> for more details...
The Internet Protocol (IP) occurs at what layer of the seven
layer
model?
A.) Physical
B.) Presentation
C.) Network
D.) Datalink
E.) Session
F.) Transport
- 2 Answers
- 4588 Views
- I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / m haja bahurudeen
Ans : C) Network
Example :
Routed protocol
Roting protocol
| Is This Answer Correct ? | 2 Yes | 0 No |
What is the difference between ‘bit rate’ and ‘baud rate’?
How does RIP differ from IGRP?
Which device listed below provides clocking for the line? A.) DCE B.) CPE C.) CO D.) DTE E.) Demarc
You have OSPF traffic flooding your network via one of your router interfaces. Write the access list line that will deny all ospf traffic. Don't worry about the other lines of the access list.
hi shyam i am putting urs question here I am facing one problem in my layer 2 switch I don’t know the problem is on switch side or client side. The problem is some PC (not all) are stop participate in LAN they don’t send or recd. Packet from switch and if I check RJ45 (with LAN tester)from PC side the packet and 8 pin wire is working fine and after that process of LAN tester I plug RJ 45 in PC now PC start recd/ send packets what is the problem I don’t understand even client side no virus found RJ45 is ok and switch has no problem bcoz other PC is working fine Cable (cat 5 ) is also fine bcoz I didn’t crimp again just check in LAN tester and start working fine. Plz any one solve this matter. And after lan tester process pc is working fine and after 2 or 3 hour it again start same problem and again same process lan tester I have used
How many LMI types are available on Cisco routers? A.) Four B.) Two C.) Five D.) Three
hi i am facing one problem.ptoblem is like that i am getting output error on mine router ethernet interfae here is the cisco#show interface e0 Ethernet0 is up, line protocol is up Hardware is QUICC Ethernet, address is 0030.802d.2a17 (bia 0030.802d.2a17) Internet address is 202.122.20.225/28 MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec) ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:00, output 00:00:00, output hang never Last clearing of "show interface" counters 05:55:07 Queueing strategy: fifo Output queue 0/40, 0 drops; input queue 0/75, 0 drops 5 minute input rate 10000 bits/sec, 11 packets/sec 5 minute output rate 29000 bits/sec, 11 packets/sec 1515202 packets input, 359100396 bytes, 1 no buffer Received 6 broadcasts, 0 runts, 0 giants, 1 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 0 input packets with dribble condition detected 1584394 packets output, 1623395338 bytes, 0 underruns 1820 output errors, 26732 collisions, 0 interface resets 0 babbles, 0 late collision, 9698 deferred 18 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out output cisco# what is the reason how to solve this please tell me i am using cisco asa 5520 behid mine internet router and no error on the asa inside interface
Why would you use static routing instead of dynamic routing? A.) When you want automatic updates of the routing tables B.) All the time C.) When you have very few routes and want to conserve bandwidth D.) When you have a gateway of last resort
What is an advantage of local area network (LAN) segmentation? A. smaller collision domains B. elimination of broadcasts C. decreased cost of implementation D. larger number of users within the same domain
Explain the difference between named and extended acl?
What command can be used to test IPX connectivity? A.) Ping 2e.000.0045.8923 B.) Ping 192.168.100.1 C.) Ping ipx 2e.0000.0045.8923 D.) Ipx ping 2e.0000.0045.8923
2500 Value in which type of access list?
CCNA 
