1. Categories >> Certifications >> Cisco Certifications >> CCNA
  2. Suggest New Category

Which two of the following are valid ways to have multiple

encapsulation

types on a single interface?

A.) This is not possible

B.) subinterfaces

C.) additional physical interfaces

D.) secondary addresses

Question Posted / guest


Which two of the following are valid ways to have multiple encapsulation types on a single int..

Answer / guest

Answer: B D

Is This Answer Correct ?    0 Yes 0 No

Post New Answer

More CCNA Interview Questions

After how long eigrp protocol advertise its routing table?

0 Answers  

On an ISDN BRI interface, the control channel is the 'D' channel. What is the rate of this channel? A.) 64 Kbps B.) 1.544 Mbps C.) 128 Kbps D.) 2.048 Mbps E.) 16 Kbps

2 Answers  

What we called 64 bit mac-address in ipv6?

0 Answers  

Which command loads a new version of the Cisco IOS into a router? A. copy flash ftp B. copy ftp flash C. copy flash tftp D. copy tftp flash

2 Answers  

1>What do you mean by Networks and Networking? 2>Difference between Vlan And Sub Interface Vlan? 3>What is Fiber Optic Media Converter? 4>What is Firewall? 5>Difference Between Layer2 and Layer3 Switch? 6>What is the function of Multilayer Switch? 7>Expalin STP? What is the Difference between STP and MST? 8>What is the Function of VTP?Explain the modes of VTP? 9>What kind of Message VTp will Send? 10>What is the Difference between Normal and Manageable Switch? 11>Difference between Local Vlan and End to End Vlan? 12>Difference between Distance Vector and Link State Routing protocol? 13>What do you mean by Backbone Fast Port? 14>what is Root Guard and BPDU Guard?

0 Answers   Gemini, SpectraNet,




In regards to TCP/IP, which class of address allows for the fewest valid Internet hosts? A.) D B.) E C.) Classes are not used in TCP/IP. D.) B E.) C F.) A

1 Answers  

Which two types of route table entries are used by a Layer 3 router to determine the appropriate path to destination? (Choose two) A. static route entry B. default route entry C. Dynamic route entry D. temporary route entry E. permanent route entry

2 Answers  

Which command should you use to create an IP standard access list? A. access-list standard 172.16.4.13 B. access-list 1 deny 172.16.4.13 0.0.0.0 C. access-list 100 deny 172.16.4.13 0.0.0.0 D. access-list 198 deny 172.16.4.13 255.255.255.255

3 Answers  

The PDU at the network layer is a ________ Packet Frame Segment Bit

5 Answers  

IP standard access lists use which of the following as a basis for permitting or denying packets? A.) destination address B.) port C.) protocol D.) source address

2 Answers  

3 router configured with RIP & Ripv2 rotuer 1- connected with router 2 having sr ip 10.0.1.2 routing : ripv2 router 2: connected with router 1 and router 3 having sr 0 ip 10.0.1.3 & sr 1 ip 11.0.1.2 routing :rip & ripv2 router 3: connected with router 2 having sr ip 11.0.1.3 routing: rip is there communication possible btween these networks ? if yes how

2 Answers  

What protocols can you use while testing Trace? A.) DECnet B.) CLNS C.) IP D.) Old Vines E.) Vines F.) Chaos

1 Answers  

For more CCNA Interview Questions Click Here
Categories