Interested to Buy Any Domain ? << Click Here >> for more details...
Identify 2 reasons for disabling CDP?
A.) If the router is not configured for RIP
B.) Save bandwidth by eliminating overhead
C.) If the router is configured for Appletalk
D.) When connected to a non-Cisco router
- 1 Answers
- 4963 Views
- I also Faced
- E-Mail Answers
Identify the X.25 addressing standard? A.) X.121 B.) X.25a C.) ITU-1 D.) Q933a
Identify the 3 key features of the Cisco Discovery Protocol? A.) Off by default B.) Will allow for the discovery of layer 3 addresses on neighbor routers C.) Verifies connectivity D.) Open standard E.) Does not require any layer 3 protocols to be configured
Identify the default values that make up IGRP's composite metric? A.) Bandwidth B.) Load C.) Reliability D.) MTU E.) Delay
Which two statements are true? (Choose two) A. Ethernet 802.3 utilizes a half duplex method for data transfer B. In a 100 MBS point to point connection a full duplex connection can provide 400 Mbs of data transfer C. Ethernet switches can use the full duplex mode to connect multiple nodes on a single pod of a switch D. Full duplex Ethernet takes advantage of UTP using one pair for transmission and the other pair for reception
in the ospf area network dr and bdr selection procedure occur let there are 4 router in that n/w r1 have the higher priority then r2 and r2 have higher priority then r3 and so on like that r1>r2>r3>r4 now as we know that selection of dr and bdr based upon the router priority so in this case r1 will be dr and r2 will be bdr now my question is that if i am going to implement 5th router which have greater priority then r1 then will it become dr atomically remember that i am not going change my 5 or 1st router property answer that one please
If a frame is received at a switch and only the destination hardware address is read before the frame is forwarded, what type of switching method is this? A.) Store-and-drop B.) Latency C.) Store-and-forward D.) Cut-through
What is a benefit of a virtual LAN (VLAN)? A. It increases the number of broadcast domains B. It decreases the number of broadcast domains C. It increases the numberr of collision domains D. It decreases the number of collision domains E. Since it is a vitual Interface it never shuts down
Sequence and acknowledgement numbers are used for? A.) Layer transitioning B.) Flow control C.) Port number addressing D.) Reliability
Select the physical interfaces that PPP can be configured on a Cisco router: A. Asynchronous serial B. HSSI C. ISDN D. Synchronous serial
Identify the 2 commands that display the clock rate configured on the serial0 interface? A.) show serial0 B.) show interface serial0 C.) show clock rate serial 0 D.) show controllers serial 0 E.) show running-config
Which statement is true regarding half duplex? A.) Only works in a point-to-point configuration B.) Allows for transmitting and receiving but not a the same time C.) Allow for transmitting and receiving of data simultaneously D.) Doubles the bandwidth
please point out the wrong steps in that l3 switch conf Building configuration…… Current configuration : 1802 byte ! Version 12.2 no service pad Service timestamps debug uptime no service-password encryptions ! hostname xxxx ! enble secret XXXXXXXXXXX(omitted) enable password jitendera kumar sinha ! No aaa new-model System mtu routing 1500 bytes ip subnet-zero ip routing ip name-server 202.x.x.x. ip name –server 203.x.x.x ip name-server 192.168.x.x ip dhcp excluded-address 172.x.x.x 172.x.x.x ! ip dhcp pool ss network 172..x.x.x 255.255.255.0 domain-name xxx.com default-router 172.x.x.x dns-server 192.x.x.x 203..x.x.x 202.x.x.x lease10 ! ! ! ! ! no file verify auto spanning-tree maode pvst spanning-tree extended system-id ! vlan internel allocation policy ascending ! interface fastethernet 0/1 no switch port ip address 172.x.x.x 255.255.255.0 ! interface fastethernet 0/2 no switch port ip address 192.x.x.x ! interface fastethernet 0/3 switcport access vlan 5 switchport mode access ! interface fastethernet 0/4 Switcport access vlan 5 Switchport mode access ! interface fastethernet 0/5 Switcport access vlan 5 Switchport mode access ! interface fastethernet 0/6 Switcport access vlan 5 Switchport mode access ! interface fastethernet 0/7 Switcport access vlan 5 Switchport mode access ! interface fastethernet 0/8 Switcport access vlan 5 Switchport mode access ! interface fastethernet 0/9 Switcport access vlan 5 Switchport mode access ! interface fastethernet 0/10 Switcport access vlan 5 Switchport mode access ! interface fastethernet 0/11 Switcport access vlan 5 Switchport mode access ! interface fastethernet 0/12 Switcport access vlan 5 Switchport mode access ! Interface fastethernet 0/13 Switcport access vlan 5 Switchport mode access ! Interface fastethernet 0/14 Switcport access vlan 5 Switchport mode access ! Interface fastethernet 0/15 Switcport access vlan 5 Switchport mode access ! Interface fastethernet 0/16 Switcport access vlan 5 Switchport mode access ! Interface fastethernet 0/17 Switcport access vlan 5 Switchport mode access ! Interface fastethernet 0/18 Switcport access vlan 5 Switchport mode access ! Interface fastethernet 0/19 Switcport access vlan 5 Switchport mode access ! Interface fastethernet 0/20 Switcport access vlan 5 Switchport mode access ! Interface fastethernet 0/21 Switcport access vlan 5 Switchport mode access ! Interface fastethernet 0/22 Switcport access vlan 5 Switchport mode access ! Interface fastethernet 0/23 Switcport access vlan 5 Switchport mode access ! Interface fastethernet 0/24 Switcport access vlan 5 Switchport mode access ! Interface vlan 1 No ip address Shutdown ! Interface vlan 5 Ip address 172.16.x.x 255.255.255.0 ! Ip default-gateway 172.16.32.1 ! Ip classless Ip route 0.0.0.0 0.0.0.0 fastethernet 0/1 172.x.x.x Ip route 0.0.0.0 0.0.0.0 fasrethernet 0/2 192.168.x.x 254 Ip http-server ! ! Control-plane ! ! Line console 0 Line vty 0 4 Password password Login Line vty 5 15 Password password Login ! end chek out the wrong steps and post it. i ma not able to ping firewall
CCNA 
