Interested to Buy Any Domain ? << Click Here >> for more details...
Identify the X.25 addressing standard?
A.) X.121
B.) X.25a
C.) ITU-1
D.) Q933a
- 1 Answers
- 4060 Views
- I also Faced
- E-Mail Answers
What is the default IPX Ethernet encapsulation? A.) SNAP B.) Arpa C.) 802.2 D.) Novell-Ether E.) SAP
what is firewall how fiarewall work how many interfaeces in the cisco pix 501 firewall what is the working of that dmz interface
hi shyam i am putting urs question here I am facing one problem in my layer 2 switch I don’t know the problem is on switch side or client side. The problem is some PC (not all) are stop participate in LAN they don’t send or recd. Packet from switch and if I check RJ45 (with LAN tester)from PC side the packet and 8 pin wire is working fine and after that process of LAN tester I plug RJ 45 in PC now PC start recd/ send packets what is the problem I don’t understand even client side no virus found RJ45 is ok and switch has no problem bcoz other PC is working fine Cable (cat 5 ) is also fine bcoz I didn’t crimp again just check in LAN tester and start working fine. Plz any one solve this matter. And after lan tester process pc is working fine and after 2 or 3 hour it again start same problem and again same process lan tester I have used
Hi Guys I am facing one problem while configuring PAP over Point to Point links. Configuration scenario is like this. ROUTER 1: (Hostname – R1) R1(config)#username R2 password CCNA2 R1(config)#interface serial 1/1 R1(config-if)ip address 10.0.0.1 255.0.0.0 R1(config-if)#lock rate 64000 R1(config-if)#encapsulation ppp R1(config-if)#ppp authentication pap R1(config-if)#ppp pap sent –username R1 password CCNA1 R1(config-if)#no shutdown ROUTER 2: (Hostname – R2) R2(config)#usename R1 password CCNA1 R2(config)#interface serial 1/1 R2(config-if)#ip address 10.0.0.2 255.0.0.0 R2(config-if)#encapsulation ppp R2(config-if)# ppp authentication pap R2(config-if)# ppp pap sent –username R2 password CCNA2 R2(config-if)#no shutdown Now problem is that, after configure the command “ppp authentication pap” the “Line protocol” status goes down on each router. But when I disable this command using “no ppp authentication pap”, the “Line Protocol” status goes up. What could be the problem, can anyone explain it plzzz….!!! Thanks in Advance…!! Shahin..
The Datalink layer works with which of the following: A.) Packets B.) Bits C.) Globules D.) Frames E.) Segments
Which statement about Ethernet networks is true? A. The advantage of a full duplex is the ability to transmit data over 111 cable B. Full duplex Ethernet requires a point-to-point connection when only two nodes are present C. Ethernet switches can use full duplex mode to connect multiple nodes to a single pod of a switch D. Half duplex is a cut through packet processing method that is vow fast little error correction Full duplex is a store and forward method that is slower but has better error correction
Regarding frame relay, which of the following statements are true? A.) You must use ANSI encapsulation if connecting to non-Cisco equipment B.) You must use IETF encapsulation if connecing to non-Cisco equipment C.) You must use Q.933a encapsulation if connecing to non-Cisco equipment D.) You must use Cisco encapsulation if connecting to non-Cisco equipment
Identify 3 characteristics of IP RIP? A.) Distance vector B.) Administrative distance is 120 C.) Periodic updates every 60 seconds D.) Uses a composite metric E.) Can load balance
What is the difference between csma/ca?
What is the function of a router?
Identify the mode reflected by the following prompt 'Router'? A.) Setup B.) RXBoot C.) Boot mode D.) Privileged exec mode
What is the purpose of data link layer?
CCNA 
