Which of the following are ways to provide login access to a router? A.) HTT

Which of the following are ways to provide login access to a
router?

A.) HTTP

B.) Console

C.) Telnet

D.) Aux Port

E.) SNMP

F.) LLC

Question Posted / guest

3 Answers
15910 Views
I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

Which of the following are ways to provide login access to a router? A.) HTTP B.) Console ..

Answer / guest

Answer: A B C D

You can connect via Aux, Console, Telnet, or HTTP to a Cisco
router.

SNMP can support Community (password protected) SET and PUT
commands,

but you can not issue a command line interface command with it.

Is This Answer Correct ?

23 Yes

6 No

Which of the following are ways to provide login access to a router? A.) HTTP B.) Console ..

Answer / saif

b,c,d is the correct answer

Is This Answer Correct ?

7 Yes

0 No

Which of the following are ways to provide login access to a router? A.) HTTP B.) Console ..

Answer / aarya

Is This Answer Correct ?

2 Yes

3 No

Post New Answer

More CCNA Interview Questions

The following commands were entered at the command prompt of a Cisco router. What do they accomplish? access-list 1000 deny 9e.1234.5678.1212 4 access-list 1000 permit -1 interface ethernet 0 ipx network 9e interface ethernet 1 ipx network 4a interface serial 0 ipx network 1 ipx output-sap-filter 1000 A. File server advertisements from server 9e.1234.5678.1212 will not be forwarded on interface S0. B. All other SAP services, other than file server, from any source will be forwarded on S0. C. All other SAP services, other than print server, from any source will be forwarded on S0. D. Print server advertisements from server 9e.1234.5678.1212 will not be forwarded on interface S0.

1 Answers

What's the default CDP holdtime in seconds for Cisco routers? A.) 30 seconds B.) 180 seconds C.) 90 seconds D.) 60 seconds

3 Answers

Explain the difference between igp and eigrp?

0 Answers

On which mode we give debug command?

0 Answers

Identify the default IPX serial encapsulation? A.) Novell-Ether B.) SDLC C.) SNAP D.) HDLC

1 Answers

Given the configuration example: interface ethernet0 ipx network 4a ipx access-group 800 out interface ethernet1 ipx network 3d interface ethernet2 ipx network tc access-list 800 permit 3d 4a Which action result from implementing this configuration? a-Traffic from network 3d for network 4a will be forwarded out e0 b-IPX network 5c will not receive any traffic c-Traffic from network 3d, destined for network 4a, will be forwarded out e2 d-Traffic from network 3d for network 3d will be forwarded out e0

0 Answers

Hi, If we create more Gateway from one our Router Interface Gateway (Example: by set up a ISA server etc) will it effect on our bandwidth to be low? please help me

5 Answers

Which router command allows you to view the entire contents of all access lists? A. Router# show interface B. Router> show ip interface C. Router# show access-list D. Router> show all access-list

3 Answers jetking,

In regards to the ISDN BRI standard, which channel is used for control? A.) B B.) D C.) E D.) I E.) Q

2 Answers

what is default route

2 Answers

What is the purpose of ARP? A.) IP to host name resolution B.) Host name to IP address resolution C.) Mac to IP address resolution D.) IP to Mac address resolution

2 Answers

What is true about frame-relay DLCI? A.) DLCI represents a single physical circuit B.) DLCI is optional in all frame-relay networks C.) DLCI identifies a logical connection between DTE devices D.) DLCI is used to tag the beginning of a frame with VLAN information

1 Answers

For more CCNA Interview Questions Click Here