Which is true regarding half duplex Ethernet operation?
A.) Half Duplex ethernet technology provides a transmit circuit
connection wired directly to the receiver circuit at the
other end
B.) Half duplex transmission between stations is achieved by
using point
to multipoint Ethernet and Fast Ethernet
C.) With Half Duplex transmission logically circuits feed
into a single
cable creating a situation similar to a one way bridge
D.) Half Duplex transmission between stations is achieved
using Point to
Point Ethernet & Fast Ethernet
Answer / guest
Answer: C
Half-Duplex - Capability for data transmission in only one
direction at
a time between sending station and a receiving station.
Is This Answer Correct ? | 8 Yes | 0 No |
Which device listed below provides clocking for the line? A.) DCE B.) CPE C.) CO D.) DTE E.) Demarc
What is the standard ISDN term for a native ISDN modem? A.) ET B.) LE C.) TE2 D.) TE3 E.) TA
Which network mask should you place on a Class C address to accommodate a user requirement of two subnetworks with a maxximum of 35 hosts on each networks A. 255.255.255.192 B. 255.255.255.224 C. 255.255.255.240 D. 255.255.255.248
switch kitne volt per work karta hai. what is frame realy. what is isdn and pri and bri.
Identify the command that configures serial0 for PPP encapsulation? A.) Router(config)# encapsulation ppp B.) Router(config-if)# encapsulation serial ppp C.) Router(config-if)# encapsulation ppp D.) Router# encapsulation ppp
Which three commands are used to configure information into RAM on a router? (Choose three) A. configure memory B. configure terminal C. configure overwrite D. copy tftp startup-config E. copy running-config startup-config F. copy startup-config running-config
Which commands should you use to enable IGRP routing? A. router igrp 100 Network 192.168.1.0 Network 10.0.0.0 B. router igrp 100 Network 192.168.2.0 Network 10.0.0.0 C. router igrp 100 Network 192.168.1.0 192 168.1.1 Network 10.2.0.0 10.2.1.1 D. router igrp 100 Network 192.168.1.0 255.255.255.0 Network 10.2.0.0 255.255.255.0
thnx jitender...its me shridh...m working for SG ltd..the situation iz like ths -at a specific time in our company the internet connectivity goes off...v hav two networks in our company...but out of it only one link goes down for 5-10 sec...a fastethernet port becomes down for few sec and automatically becomes Up... Is this occures becoz of Power?? If yes thn y the 2nd network is not affected?? plz tel me jitender how to resolve ths problem? as u sd loop in switch is the primary cause of ths....i wanna know how to resolve it...thnx for ur replys jitender sinha.
On a network design project you determine that a new testing application requires multiple hosts. These hosts must be capable of sharing data between each host and an enterprise server at 10 Mobs bandwidth. Other divisions in the company use applications that require less than 2 Mobs bandwidth of the enterprise server. What is your most economical recommendation? A. That existing 10BaseT hubs be replaced with 1 00BaseT hubs to improve overall performance B. That a router can separate the testing application from the rest of the network, thus allowing the testing application more bandwidth. C. That a switch be installed, so that the enterprise server can be provided a 100 Mobs pod and each of the testing application hosts can be given dedicated 10 Mobs pods] D. That a bridge be placed between the enterprise server and all other users with the exception of the testing application
Identify the 2 commands to copy a configuration from a TFTP server to RAM? A.) configure network B.) configure overwrite C.) copy backup-config running-config D.) copy tftp running-config
What are the advantages of layered model in networking industry?
Which layer is responsible for negotiating data transfer syntax? A.) Network B.) Session C.) Application D.) Transport E.) Presentation