What does the show protocol display?

0 Answers  

---

In order to configure a Frame Relay subinterface with IP identify the 2 commands that must be configured on the physical interface? A.) Router(config-if)# encapsulation frame-relay B.) Router(config-if)# no ip address C.) Router(config-if)#encapsulation subinterface frame-relay D.) Router(config)# subinterface s0 encapsulation frame-relay

1 Answers  

---

FastEthernet compares to 10baseT Ethernet in which of the following ways

1 Answers  

---

If a frame is received at a switch and only the destination hardware address is read before the frame is forwarded, what type of switching method is this? A.) Store-and-drop B.) Latency C.) Store-and-forward D.) Cut-through

2 Answers  

---

Which of the following are examples of the Application Layer? A.) LLC B.) Token Ring C.) Spreadsheet D.) TCP E.) IP F.) Word Processor

1 Answers  

---

Which of the following is a layer 2 device? A.) Switch B.) Router C.) Repeater D.) Hub

4 Answers  

---

Regarding frame relay, which of the following statements are true? A.) You must use ANSI encapsulation if connecting to non-Cisco equipment B.) You must use IETF encapsulation if connecting to non-Cisco equipment C.) You must use Q.933a encapsulation if connecting to non-Cisco equipment D.) You must use Cisco encapsulation if connecting to non-Cisco equipment

2 Answers  

---

Which protocol resolves an IP address to a MAC address? A.) DHCP B.) RARP C.) ARP D.) NBP E.) DNS

4 Answers  

---

GUY i Have attended one interview for the data craft and they are offering me L1 postion and i am working at l2 in cisco so there is no way to get in the datacraft i am posting here the question he asked to and i have tested the interviewer and i come to know he was not having any knowledge. His questions are-: 1) what is Vlan 2) what is stp and what is difference between stp and RSTP 3) what is HSRP and Diffrence betwwen HSRP and GLBP 4) how to configure HSRP 5) Scenario Based question ( if we have two router and both are connected and there are having redundancy means two interface of the router r1 is connected to the two interface of Router R2 (R1)-------------(R2 (R1)-------------(R2 Now he want to configure the router in such a Manner that if one link down second link should come up.My answer was HSRP and his is "F looting static routing was i wrong "i know F looting Static routing is Theoretically possible but it is not fusible in the scenario where you have multiple router connected to the same router and if you have configured sub interface i challenged him and he lost The Battle and he get angary 5) what the eigrp and how it works 6) tables in eigrp 7) the information of feasible successor where it saved now after answering these all he was very angry ( i can fill the heat) 8) then he come to ospf Area type ( he was also not aware) 9) LSA type and its working ( he was also having confusion ) 10) then is asked routing by rummer( Theroy) 11) hello and dead intervel of EIGRp (theory) 12) Selection cretaria for Eigrp slecting best path ( here we have a long discussion on MTU and he lost the battle and agree That MTU never comes in the accounts in this process) 13) what is ACL type of acl ( here he was aware of TWO type Standard and extended i have told him 5 type( he again get Angry) We have 2hr of discussion and and he told me he will call me latter but i know he never call

1 Answers   IBM,

---

How are internetworks created?

0 Answers  

---

What command will display all connected OSPFv2 routers?

1 Answers  

---

Identify the length of an IPX address and it's components? A.) 80 bits, 48 bits network and 32 bits node B.) 32 bits, 16 bits network and 16 bits node C.) None of the above D.) 80 bits, 32 bits network and 48 bits node

1 Answers  

---