Which addresses are INCORRECTLY paired with their class?

A. 1 to 126, Class A

B. 128 to 191, Class A

C. 1 to 126, Class B

D. 128 to 191, Class B

Answers were Sorted based on User's Feedback



Which addresses are INCORRECTLY paired with their class? A. 1 to 126, Class A B. 128 to 191, C..

Answer / m haja bahurudeen

Ans : B & C


Class A : 1 - 126 (127 assign loopback address)
Class B : 128 - 191
Class C : 192 - 223
Class D : 224 - 239
Class E : 240 - 255

Is This Answer Correct ?    11 Yes 0 No

Which addresses are INCORRECTLY paired with their class? A. 1 to 126, Class A B. 128 to 191, C..

Answer / guest

Answer::B & C.

Address classes are: 1 to 126, Class A; 128 to

191, Class B, 192 to 223, Class C; 224 to 239, Class D; and

240 to 255, Class E.

The first octet rule states that the class of an address can

be determined by the numerical value of the first octet.

Is This Answer Correct ?    7 Yes 0 No

Which addresses are INCORRECTLY paired with their class? A. 1 to 126, Class A B. 128 to 191, C..

Answer / kapilasdhir

B. 128 to 191, Class A

C. 1 to 126, Class B

Is This Answer Correct ?    6 Yes 0 No

Post New Answer

More CCNA Interview Questions

what are two security appliances that can be installed a network

9 Answers  


Station A is transmitting data to station B faster that station B can handle it. When station B's buffer fills up, it send out a message to station A to stop sending data. After B empties out its buffer, station B sends a message to station A to start sending data again. This is most directly an example of (pick the best answer only): A.) Poison Reverse B.) Connectionless protocol C.) Windowing D.) Connection oriented protocol E.) Flow Control F.) Split Horizon

1 Answers  


What is the default interval for SAP updates? A.) 60 seconds B.) 15 seconds C.) 30 seconds D.) 120 seconds

1 Answers   ACS,


Identify 2 functions of IPX access-lists? A.) Control SAP traffic B.) Limit number of Novell servers on a network C.) Limit number of workstations on a network D.) Block IPX traffic

1 Answers  


Which of the following would not be displayed by the command ?sho cdp neighbor detail?? A.) The incoming/outgoing interface. B.) The hardware platform. C.) One address per protocol. D.) Amount of Flash Memory Available E.) The routers hostname. F.) The subnet mask, if IP is configured.

1 Answers  






Suppose there are 3 pc's pc1 pc2 and pc3 all are connected with each other pc 1 is able to ping pc2 and pc3 but pc2 and pc 3 not able to ping pc 1 then what is an issue troubleshoot it?

0 Answers   Wipro,


A ISDN PRI circuit can be described as which of the following? A.) 24 B channels and 1-64Kbps D channel B.) 23 B channels and 1-64Kbps D channel C.) 2-D channels and 1-C channel D.) 2-64Kbps B channels and 1-16Kbps D channel

1 Answers  


Which can be logged by IPX extended access lists? A.) source address B.) protocol C.) source socket D.) access list number E.) destination socket F.) destination address

1 Answers  


What 2 commands verify end to end communications? A.) Trace B.) debug ip session C.) Ping D.) Route

1 Answers  


Where is the backup configuration file stored? A.) RAM B.) ROM C.) Console D.) NVRAM

1 Answers  


Which protocol will send a message to routers if a network outage or congestion occurs? A.) ARP B.) TCP C.) IP D.) ICMP

2 Answers  


What is the regional telco office called, where the customers local loop terminates? A.) Demarc B.) DTE C.) DCE D.) CO E.) CPE

1 Answers  


Categories