Automobile Engineering Interview Questions, Answers for Freshers and Experienced asked in various Company Job Interviews

Automobile Engineering Interview Questions

Questions Answers Views Company eMail

The permanent reduction provided by the final drive in car is a) 4:1 b) 6:1 c) 8:1 d) 10:1

Backbone, Bosch, MAHINDRA, Uniparts Group,

1268

The permanent reduction provided by the final drive in heavy vehicle is a) 4:1 b) 6:1 c) 8:1 d) 10:1

Backbone, Bosch, MAHINDRA, Uniparts Group,

1319

Single reduction is used in final drive when it is about a) 6:1 b) 8:1 c) 10:1 d) 12:1

Backbone, Bosch, MAHINDRA, Uniparts Group,

1358

The function of Differential is a) To prevent wheel skidding b) To reduce the speed of the inner wheels during turning c) To keep the speed of all the wheels same when going straight ahead d) all of the above

Backbone, Bosch, MAHINDRA, Uniparts Group,

1469

The crown wheel of the final drive is connected to a) Cage b) Spider c) Cross pin d) Axle half shaft

Backbone, Bosch, MAHINDRA, Uniparts Group,

1454

In a vehicle, which is going straight ahead at N rpm, if the left wheel rotates forward at n rpm, then the resultant speed of the right wheel will be a) N+n b) N-n c) N/n d) Nn

Backbone, Bosch, MAHINDRA, Uniparts Group,

1451

What is the main task of batter in an automobile?

John Deere,

1007

Which mechanism is used in automobile gearing?

GM General Motors,

1208

What Is Hess's Law? State its implications.

Ashok Leyland,

1106

Describe Hooke's Coupling and its uses.

Ashok Leyland,

1261

What is Kirchhoff's Law ?

Ashok Leyland,

1071

Define Poisson's ratio.

Ashok Leyland,

1093

Define Hook's law.

Ashok Leyland,

986

What is Brinell's hardness test ?

Ashok Leyland,

1050

What do you understand by Newtonian Fluid? Where is it used?

Ashok Leyland,

1050

Post New Automobile Engineering Questions

Un-Answered Questions { Automobile Engineering }

Axial force to keep the clutch in engaged position is provided by a) Springs arranged circumferentially b) Pressure plate c) Flywheel d) Clutch pedal

1389

Why oil is mixed with coolant and what are causes of this?

957

Explain Rankine cycle.

1008

engine rotation

1870

1.what is the minimum percentage for engineering students? I like to become RTO officier...please send me procedure for that...

3179

Slip joints are provided in the propeller shaft a) To adjust the inclination of the propeller shaft b) To adjust the length of the propeller shaft c) To prevent the whirling of the propeller shaft d) To adjust the up and down movement of the rear axle

1347

i have chines vehicle Grand Tiger now its AC compressor become jam what should i do i have not found new in market

2521

Why different types of sound are produced in different bikes though they are run on Si engine

1049

What is standard size journal and big end crankshaft in mahindra bolero

1937

What is an injector pressure in heavy vehicle?

1213

How bhp can be calculated in si units?

1138

The Hook's joint works efficiently when the propeller shaft inclination is a) 18o b) 28o c) 38o d) 48o

1318

what is the syllabus for the rrb sec. eng. posts iam from automobile engg.

2515

The friction plate is always mounted on a) flywheel b) Pressure plate c) Internally splined hub d) Clutch spring

1540

For the second gear in a synchromesh system, the drive transfer will be through a) U1, U2, C, F2, and splines b) U1, U2, C, F1, and splines c) U1, U3, D, F3, and splines d) U1, U4, U5, E, F2, and splines

1377

For More Un-Answered { Automobile Engineering } Questions Click Here