Answer / guest

Answer: A

Answer / senthil

A.) Router(config)# router igrp 100

Answer / anand gupta

A.) Router(config)#router igrp 100

What is the virtual channel?

0 Answers  

---

which utility should use to test whether TCP/IP has been initialized on a system.friends plz post the answer with explaination..

3 Answers  

---

Identify the default values that make up IGRP's composite metric? A.) Bandwidth B.) Load C.) Reliability D.) MTU E.) Delay

1 Answers  

---

Which ISDN protocol prefix specifies switching and signaling? A.) I B.) E C.) Q D.) S

1 Answers  

---

Suppose we have 4 switches runing in VTP mode. So when i create a VLAN in Server Switch this VLAN info reflect in all other switch. So question is - A) Suppose i m practicing this scenario in BOSON software, When a create a VLAN in server switch n ADD ports of switch to that VLAN, the same number of ports of client switch also belongs to dat VLAN. For example - In switch A (Server mode), i create a VLAN 7 name Hyderabad & port number 1, 2 & 3 put into this VLAN. Another Switch B (Client mode), its also showing that port number 1,2 & 3 belong the same VLAN. How cud it possible... As we know, VTP share only VLAN configuration information. Cud anyone explain it please....!!!! B)Same thing, when i m practicing in PACKET TRACER 5.0, its only showing that VLAN configuration information is shared. No port information is shared at all. I can manually configure individual switch port to respective VLAN as our wish. Cud anyone explain it please..!!!

3 Answers  

---

Which two does 100BaseT use? A.) CSMA/CD B.) IEEE 802.5 C.) 802.3u D.) Switching with 53-byte cells

3 Answers  

---

Although Cisco IOS 11.2 and later can auto-detect the LMI type in Frame Relay, which command will force the LMI type to q933a? A.) frame-relay lmi-type q933a B.) encapsulation frame-relay q933a C.) don't need to, it is the default D.) encapsulation q933a E.) encapsulation frame-relay type=q933a

1 Answers  

---

Identify 3 UDP characteristics? A.) Reliable communication protocol B.) Applications that use UDP must incorporate reliability C.) Connection-less oriented D.) Incorporates no handshaking

2 Answers  

---

What 3 sources can configuration commands be placed into RAM? A.) HP Openview B.) Console C.) Vterminal D.) TFTP server E.) NVRAM

1 Answers  

---

How can we configure Inter-VLAN in Layer 3 Switch? Remember one thing without Router.

7 Answers   Grace, HCL,

---

Which of the follwing are true of standard half-duplex Ethernet circuitry? A. It is alternate one-way communication B. The receive (RX) is wired directly to the transmit (TX) of the remote station C. The transmit (TX) is wired directly to the receive (RX) of the remote station D. Collisions are not possible E. Both stations can transmit simultaneously

2 Answers  

---

Hi Guys I am facing one problem while configuring PAP over Point to Point links. Configuration scenario is like this. ROUTER 1: (Hostname – R1) R1(config)#username R2 password CCNA2 R1(config)#interface serial 1/1 R1(config-if)ip address 10.0.0.1 255.0.0.0 R1(config-if)#lock rate 64000 R1(config-if)#encapsulation ppp R1(config-if)#ppp authentication pap R1(config-if)#ppp pap sent –username R1 password CCNA1 R1(config-if)#no shutdown ROUTER 2: (Hostname – R2) R2(config)#usename R1 password CCNA1 R2(config)#interface serial 1/1 R2(config-if)#ip address 10.0.0.2 255.0.0.0 R2(config-if)#encapsulation ppp R2(config-if)# ppp authentication pap R2(config-if)# ppp pap sent –username R2 password CCNA2 R2(config-if)#no shutdown Now problem is that, after configure the command “ppp authentication pap” the “Line protocol” status goes down on each router. But when I disable this command using “no ppp authentication pap”, the “Line Protocol” status goes up. What could be the problem, can anyone explain it plzzz….!!! Thanks in Advance…!! Shahin..

6 Answers  

---