here is your question sahin Hi Jitendera, If i m not wrong, then in EIGRP, Metric weight is set to K1(Bandwidth)=1, K2(Delay)=0, K3(Reliability)=1, K4(Load)=0, K5(MTU)=0. This is default setting for EIGRP. I knew about it from ICND 2 cisco press book. Three more questions - a) If we change the K value (I mean metric weight)on a router what will happen??? b) When redistribution is necessary in EIGRP. Is there any condition for that??? c) What is reference bandwidth for metric calculation in EIGRP. As we know, in OSPF, on a CISCO router reference bandwidth is 10Mbps.

Hi Jitendera, I need ur suggestion. I completed my CCNA certification & also hving some sort of real time experience. Now i m planning to do CCNP. Little bit confusion is that whether it wud be better for me to go for CCNP ya CCNA (Security). As off my goal is to reach CCIE (Security & Switching/Routing). So tell me some solution of my confusion yaar..!!! Thanx & Regards Shahin..

Hi Jitendera, Wat do u do..?? I mean r u working anywhere???? Basically where r u from??? If u don't hv any problem, u can say..?? Or else mail me mr.shahin07@gmail.com

HCL, Wipro,

what is the diffination of bandwidth.

Can anyone explain the STP Security features. Just like BPDU guard, Root Guard. Hi JITENDERA, i m specially looking for u?????

Can anyone explain the load balancing of PVST+????

The administrator of a comapny needs to ensure that a web server in their network is accessible from the Internet. Since the network uses private addressing, this requires an IP-to-registered-address mapping. The following command is entered on the router: router(config)# ip nat inside source static 192.168.2.1 198.18.1.254 After unsuccessful results from a ping to the Internet, the administrator issues the show ip nat translations command and the output is blank. What could be the problem with the NAT configuration for this mapping? A. The keyword overload is missing from the command. B. The administrator needs to define a NAT pool first. C. An access list must be defined to create static NAT translations. D. The interfaces need to be configured for NAT.

What is switch priority & why it is used????

ADP,

what hapeen we we configure default root on the router which is conected by isp supoese there are two router r1 is conected throug isp and and by s0 r1 is conexted to r2 if we apply degault root on r1 what will happen

Hi Jitendera, I continuously read your answers which is more knowlegable than books... Q.I am facing some problems in subnetting.can you plzz explain the subnetting process.. will be remain thankful

What is the difference between DTE & DCE???

ISDN, Wipro,

What is CSU/DSU & explain the function????

Cisco,

take a pen and copy before solving that question there is a router name Ra there is two switch sw1 and sw2 sw1 is coneceted through fa0/1 interface of router Ra sw2 is conected through the fa1/1 serai interface of router s0/1 conected through the isp with it ip address 192.168.1.1 now therer are three host conexted through the sw1 and having ip host1=10.1.2.1 host2=10.1.2.2 host3=10.1.2.3 now there is also 3ree host conected through switch 2 i.e sw2 having ip host4=10.1.1.1 host 5=10.1.1.2 host 6=10.1.1.3 now i think u have made corect confrigation.now questios is started network admin configure the Ra router in that fassion Ra(config)#access-list 2 permit 10.1.1.0 0.0.0.255 Ra(config)#line vty 0 4 ra(config)#access-class 2 in now question is that why should network admnistratoe do it in this maneer A to give access sw1 host to acess internet B to prevent sw1 host from acessing comand promt c to prevent sw2 host from accessing console of router ra D to give sw2 host access to the enternet e prevent sw1 host from accessing internet f to prevent sw1 host from acessing the sw2 host network isp------(s0/1)..RA..(fa1/1)---SW2-host (4,5,6) | | (sw1)------host 1,2,3 this is not exect digarm but help to derive the diagram plz answer as soon as possible

AT&T,

while trouble shooting a network conectivty prob a technician observes that steady link light on the both work stations nic and the switch port which the workstation is conected.however when the ping comand is issuede from the work station the out message is request time out at which layer of osi model does the prob most likly exist 1 sessiom layer protocol layer datalink kayer acess layer network layer application layer i have ansered n/w layer but i am niot sure i have also posted privous question jitendera kumar sinha

1 what is the number of telnet session in the cisco router a 1 b 2 c 3 d 4 e 5