Company Name Starts with ...
#  A  B  C  D  E   F  G  H  I  J   K  L  M  N  O   P  Q  R  S  T   U  V  W  X  Y  Z

Bosch Interview Questions
Questions Answers Views Company eMail

Axial force to keep the clutch in engaged position is provided by a) Springs arranged circumferentially b) Pressure plate c) Flywheel d) Clutch pedal

 1 1465

The friction plate is always mounted on a) flywheel b) Pressure plate c) Internally splined hub d) Clutch spring

 1 1649

The main advantage of single plate clutch over cone clutch is a) Easier gear changing b) Less binding of contact surfaces c) Less pedal movement d) all of the above

 1 1758

The main function of transmission is a) To provide means to vary the torque ratio between the engine and the road wheels b) To provide neutral position c) To provide means to back the car d) all of the above

 1 1561

The resistance to the vehicle motion whose magnitude remain constant with respect to the vehicle speed is a) Resistance due to gradient b) Resistance due to the road c) Resistance due to the tyre friction d) all of the above

 1 1592

The resistance to the vehicle motion whose magnitude various with the square of the vehicle speed is a) Resistance due to gradient b) Resistance due to road c) Resistance due to the tyre friction d) Resistance due to wind

 1 1334

If the tractive effort is the highest for a given velocity, then the vehicle must be in a) Top gear b) Third gear c) Second gear d) First gear

 1 2042

The point of interaction of the tractive effort curve and the total resistance curve is called a) Stabilizing speed point b) Low speed point c) High speed point d) Normal speed point

 1 1391

If the given tractive effort curve and the total resistance curve does not intersect, then a) The vehicle will accelerate b) The vehicle will decelerate c) The vehicle will not be able to go at this gradient for the given gear d) None of the above

 1 1271

The main disadvantage of sliding mesh type of gear box is a) High noise level b) Low mechanical efficiency c) High skill required by the driver d) all of the above

 1 1350

Double declutching is used for the engagement of gears in a) Sliding mesh type of gear box b) Constant mesh type of gear box c) Synchromesh type of gear box d) None of the above

 1 1350

High speed gear is obtained in the case of sliding mesh gear box when a) Motion is transferred through the clutch gear to lay shaft gear b) Main shaft is coupled to the clutch shaft c) Smallest gear on the lay shaft is engaged d) Largest gear on the lay shaft is engaged

 1 1371

The Figure 1 depicts a) Top gear b) Second gear c) First gear d) Reverse gear

 1 1281

In case of a constant mesh gear box, when the left dog clutch is slid to the left by means of the selector mechanism, a) Direct gear is obtained b) First gear is obtained c) Second gear is obtained d) Reverse gear is obtained

 1 1362

In a constant mesh gear box, when the right dog clutch is engaged with the gear on the right side of the main shaft, a) Direct gear is obtained b) First gear is obtained c) Second gear is obtained d) Reverse gear is obtained

 1 1328

Post New Bosch Interview Questions


Bosch Interview Questions


Un-Answered Questions

Write short notes on any three of the following: (i) Domino Effect (ii) Functional and Dysfunctional conflict (iii) Formal and Informal groups (iv) MBO (v) Organizational Culture and Climate

2561

1. When u r checking out what ll happens for version no? a. Increase b. decrease c.reset to 0 d. reset to 1 e. no change 2. Salary of all employees needed to add with the commision. What transfrmation to be used? a. SQ and Expression b. SQ c. Update Strategy d. Expression 3. Which of the task is used to run a session based on success of the other session? a. Decision b. Event wait c. Email d. Command e. None 4. Types of sources in Informatica? a. Homogenous n Heterogenous b. None c. Cobol n XML d. Flat files e. Flat files and Homogenous n Heterogenous 5. Servers are available in informatica? a. Informatica Server and Workflow server b. Informatica Server and Informatica Repository Server c. Informatica Server d. Workflow server e. Informatica Repository Server 6. While using Pmcmd in cmd line mode, each command must include the connection info of which of the following? a. workflow manager b. Power Center server c. Workflow monitor d. Repository manager e. Designer 7. Workflow montior displays workflows that have run a. once b. twice c. never d.four times e. thrice 8. Mode for handling sessions n workflows? a. server mode b. Wait mode c. Command line mode d. User mode e. Interactive mode 9. Connection details configured in? a. Mapping designer b. Workflow manager c. Workflow monitor d. Repository manager e. Worklet designer Thanks in Advance

4268

Can anyone send me question papers for section engineer for railways and send me on my id- abhay_jg@yahoo.com

2129

How is a function declared? Why are Kotlin functions known as top-level functions?

309

can any send me a forbes marshall dtron 316 manual

2035

hai friends i have BSNL JTO exam on next month so if any body have model question paper or give preparation tips to my mail id kumar4486@yahoo.co.in this will helpfull for my future .plz & thank u by kumar

2072

Connecting to iserver volume using idapi classes(java classes) and after connecting to iserver I want to execute the rox on iserver and also want know the status whether that job is succesfully run or not?

1106

Explain how to edit location for weather?

960

who is your favourate actor in tollywood tellme about him in few points

3124

how do you get on with your current boss

2397

I need to constructive work in amaraj batteries

1937

Explain filters in zend framework with examples?

274

Hi, Please post in here the Aptitude Test Questions given in companies like Thomson, Reuters, GMS, JP Morgan, Northern Trust Bank etc.

6757

how to get no of items from from weblist?

1964

What are the ratings of VCB, MCB, MCCB, SF6, ACB, and OCB?

1644