An electron is injected into a region of uniform magnetic flux density with the components of velocity parallel to and normal to the flux. What is the path of the electron?

1928

The height to which the liquid in a tank to be maintained for a certain constant velocity?

1531

Write a program to implement the motion of a bouncing ball using a downward gravitational force and a ground-plane friction force. Initially the ball is to be projected in to space with a given velocity vector.

1947

2. Dry saturated steam at 3.5 bar is expanded through a convergent nozzle to 2.2 bar. The exit area is 5 sq. cm. Calculate the exit velocity and mass flow rate, assuming isentropic expansion and super saturated flow. b) A cast iron cylinder head is fastened to a cylinder of 750mm bore with 12 stud bolts. The maximum pressure inside the cylinder is 3 Mpa. The stiffness of part is thrice the stiffness of the bolt. What should be the initial tightening load so that the point is leak proof at maximum pressure? Also choose a suitable bolt for the above application 2 The propeller shaft of a marine engine is to transmit 600 kW at 1200 rpm, without a significant bending. The efficiency of the propeller is 88% at 32 knots ( 1 knot = 1085 km/hr). If the slenderness ratio is less than 50 and the permissible shear stress should not exceed 65 Mpa. Determine the diameter of shaft. 3 A semi-elliptic leaf spring consists of two extra full-length leaves and six graduated length leaves, including the master leaf. Each leaf is 7.2 mm thick and 65 mm wide. The centre-to-centre distance between the two eyes is 1.3m. The leaves are pre-stressed in such a way that when the load is maximum, stress induced in all leaves are equal to 380 N/mm sq. Determine the maximum force that the spring can withstand

1810

1)we have 1000 cfm Blower,Dia-1Mtr,Velocity of air 94 m/s 2)We have Natural Air velocity 94m/s 3If i Put Wind Mill in natural air ,speed is 94m/s Then it will generate Assume 100kw 4)If i put same wind mill across the Blower,air speed is same 94m/s now the Question is Will it generate 100 kw?

1521

what is the minimum velocity of cooling water for maximum efficiency of condensor.

1772

the water is flowing through a velocity of 1.5m/s in a pipe of length 2500m and dia 500mm. at the end of pipe a valve is provided. find rise in pressure 1. if the valve is closed in 5 seconds. 2. if the valve is closed instantaneously. take value of c = 1460m/s, pipe to be rigid and bulk modulus of water - 19.692x10' n/sqcm

1890

what is the velocity considering in lube oil drain line for lube of system for steam turbine?

1658

what is orfics working in main steam line. is it increase pressure, velocity of steam flow and dicrease steam flow rate. or any other

1690

Given, T1=600C, constant temperature of wall 800 , length of wit exchanger L=3m, dia=25 mm, Cp=14.91 KJ/kg.K, density ρ=914 kg/m3,mean velocity vm= 2 m/s, film heat transfer coefficient hf=72 Kcal/h.m2.K, what is the outlet temperature?

1617

22. A solution of 1% (w/v) starch at pH 6.7 is digested by 15 μg of β‐amylase (mol wt 152,000). The rate of maltose (mol wt = 342) had a maximal initial velocity of 8.5 mg formed per min. The turnover number is

5986

What is turnover velocity?

4532

when air is supplied from larger diameter pipe with some pressure if change diameter to small pipe the pressure increases or not? also what is increased pressureor velocity?

1355

A set of N billiard balls are set on a one-dimensional table. The table is 1 meter long, set north-south with two pockets at either side. Each ball has zero width and there is no friction so it is moving with a fixed velocity of either northward or southward and bounces back in a perfect elastic collision from other balls it encounter on its way (or drop into one of the pockets). Your job is to keep track of the balls movements. Task Please write a program that gets the initial place, speed and direction of all the balls and gives the position of a specific ball after t seconds. Input The first line contains the number of scenarios. Each one of the other lines in the input contains a scenario: The first number, N, is the number of balls; followed by N pairs of numbers: the distance in centimeters from the south end of the table and the speed (positive speed meaning it moves northward); the last two numbers are the number i of the target ball you should track and the time T in seconds. Output The output is a single number for each line which is the place (distance in centimeters from the south end of the table) of the tracked ball after T seconds. Note: There is no new line character at the end of the result. Sample Input 5 1 50 1 1 1000 1 50 1 1 6 1 60 -2 1 6 2 10 1 95 -1 2 30 2 10 1 95 -1 2 60 Sample Output 100 56 48 65 70

2137

how to calculate steam velocity on tg i/l ?

1483