Answer / jitendera sinha

it is very lenthy to explan

but
i try to expian
from ccontrol paneel
activate network bridging after instalation of nic card

vereyfi
in cmd mode
tyope
show netsh bridge

if that succesfull then
u have put the nic in premisious mode

Which of the following is an example of the Physical Layer? A.) TCP B.) ARP C.) IP D.) FDDI E.) LLC F.) Fast Ethernet

2 Answers  

---

Which statement about the data link connection identifier (DLCI) is true? A. It is a number that identifies a local virtual circuit in a Frame Relay network B. It is a signaling standard between the CIDE device and the Frame Relay switch C. It is the clock speed (pod speed) of the connection (local loop) to the Frame Relay Cloud D. It is the Maximum number of uncommitted bits that the Frame Relay switch will attempt to transfer beyond the Committed Information Rate (CIP)

2 Answers  

---

What is the protocol number for TCP? A.) 80 B.) 21 C.) 11 D.) 6

3 Answers  

---

Which two commands show your access lists? (Choose two) A. show filters B. show access-lists C. show ip access-lists D. show running-config

2 Answers  

---

Identify the command to configure ALL the default VTY ports? A.) Router(config)# line vty 0 4 B.) Router# line vty 0 4 C.) Router(config)# line vty D.) Router(config)# line vty 0

2 Answers   Accel, CMS,

---

Which command listed below sets the banner message when someone connects to the router? A.) message # B.) banner # C.) login banner # D.) description # E.) login description # F.) banner motd #

2 Answers  

---

what is AD Value?

5 Answers   Cisco, Infosys,

---

What is ‘round-trip time’?

0 Answers  

---

What is the difference between ‘bit rate’ and ‘baud rate’?

0 Answers  

---

What does a router do with a packet that it does not have a destination network for? A.) Sends it to the Serial port B.) Drops the packet C.) Sends it back out the same interface it received it in D.) Forwards the packet to the next hop

1 Answers  

---

Which command would configure Interface E0 with an IP address of 12.23.4.5 using a Subnet mask of 255.255.255.0 ? A.) ip address 12.23.4.5 255.255.255.0 B.) ip address 12.23.4.5 /24 C.) ip address 12.23.4.5 mask 255.255.255.0 D.) ip address 12.23.4.5 mask ff:ff:ff:0 E.) that is an invalid mask for a class 'A' address

3 Answers   Wipro,

---

hi friends i donot know this is the networking question or not but if you help me then i will thankfull to you the problem is like that in my comnay there are 200 user which log one at a time now only one user is not able to get the dhcp address and othr are geting the dhcp my company sys admin is saying that this is the n/w fault while i am saying that this is not the n/w fault for the cleaerfication of my side i take a straight workng cable and connect that user directly to my cisco 24port switch now problem is stiil like that but one thing i wan to say he is geting manually ip and able to access internet he is able to ping the server but whrnever he tyeme \\<ip address of server> error comes like networl path provided not accepted by provider some thing like that. my systm admin is saying that i have o do somthing on my firewall but i am saying that no issue with firewall in that i connect my latop to the spefic port from where the user is conected then i am geting dhcp ip address and i am able to connect the server also i donot know why this is happen my syadmin is senior to me so i canot blame him plz help e what to do i am very weak in the filed of systym jitendera kumar sinha

6 Answers  

---