Interested to Buy Any Domain ? << Click Here >> for more details...
A company running RIP V1 protocol on their 2 seperate
networks, each nw has 14 routers, if the two nw wants to be
merged with each other total no of routers will be 28. but
rip metric is hop count(15). What needs to be done if this
setup needs to be work ?
- 2 Answers
- 6062 Views
- Satyam, I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / surya
By using same RIP it is not possible.As we can't modify the
hop count.we need to configure other than RIP (e.g. OSPF,
EIGRP).
Thanks
Surya
| Is This Answer Correct ? | 5 Yes | 0 No |
GUY i Have attended one interview for the data craft and they are offering me L1 postion and i am working at l2 in cisco so there is no way to get in the datacraft i am posting here the question he asked to and i have tested the interviewer and i come to know he was not having any knowledge. His questions are-: 1) what is Vlan 2) what is stp and what is difference between stp and RSTP 3) what is HSRP and Diffrence betwwen HSRP and GLBP 4) how to configure HSRP 5) Scenario Based question ( if we have two router and both are connected and there are having redundancy means two interface of the router r1 is connected to the two interface of Router R2 (R1)-------------(R2 (R1)-------------(R2 Now he want to configure the router in such a Manner that if one link down second link should come up.My answer was HSRP and his is "F looting static routing was i wrong "i know F looting Static routing is Theoretically possible but it is not fusible in the scenario where you have multiple router connected to the same router and if you have configured sub interface i challenged him and he lost The Battle and he get angary 5) what the eigrp and how it works 6) tables in eigrp 7) the information of feasible successor where it saved now after answering these all he was very angry ( i can fill the heat) 8) then he come to ospf Area type ( he was also not aware) 9) LSA type and its working ( he was also having confusion ) 10) then is asked routing by rummer( Theroy) 11) hello and dead intervel of EIGRp (theory) 12) Selection cretaria for Eigrp slecting best path ( here we have a long discussion on MTU and he lost the battle and agree That MTU never comes in the accounts in this process) 13) what is ACL type of acl ( here he was aware of TWO type Standard and extended i have told him 5 type( he again get Angry) We have 2hr of discussion and and he told me he will call me latter but i know he never call
Identify the mode reflected by the following prompt 'Router'? A.) Setup B.) RXBoot C.) Boot mode D.) Privileged exec mode
Identify the command that displays ethernet0/1 interface status? A.) show interface ethernet0/1 B.) show interface ethernet e0/1 C.) show interface ethernet0.1 D.) show ethernet0/1
Why ip address called logical address?
When a Distance Vector routing protocol detects that a connected network has gone down, it sends out a special routing update packet, telling all directly connected routers that the distance to the dead network is infinity. This is an example of which routing technology? A.) ICMP. B.) Only Link State routing protocols have this intelligence. C.) Triggered updates. D.) Garrison-4. E.) Split Horizon. F.) Poison Reverse.
What is the difference between tracert and traceroute?
Which 2 commands shows the Cisco IOS filename? A.) show IOS B.) show ver C.) show flash D.) show mem E.) show NVRAM
What is the terminal emulation, in which layer it comes?
How do you go to privileged mode? How do you switch back to user mode?
Which mode we can't skip when we come back from interface mode?
Where is the point between the customers site and the phone carrier that responsibility changes? A.) CO B.) Demarc C.) DCE D.) DTE E.) CPE
What parameter is used with statically assigned routers to tell packets which interface to use to reach a distant network? A.) Mask B.) Subnet C.) Default gateway D.) Interface
CCNA 
