Completely describe the steps based on OSI Model, what happens when you enter the address http://google.com in browser?? Summarize the complete steps based on layered OSI approach.

3 Answers   Cisco, Intel, TCS, Trimble Navigation,

---

The CSMA/CD Ethernet IEEE committee is defines as which of the following? A.) 802.2 B.) 802.3 C.) 802.4 D.) 802.5

1 Answers  

---

Identify the 2 commands that will display the status and information about interface E0 only? A.) show interface ethernet E0 B.) show interface E0 C.) show E0 D.) show int E0 E.) show interface

1 Answers  

---

What is the subnet? Why is it used?

0 Answers  

---

I am facing one problem in my layer 2 switch I don’t know the problem is on switch side or client side. The problem is some PC (not all) are stop participate in LAN they don’t send or recd. Packet from switch and if I check RJ45 (with LAN tester)from PC side the packet and 8 pin wire is working fine and after that process of LAN tester I plug RJ 45 in PC now PC start recd/ send packets what is the problem I don’t understand even client side no virus found RJ45 is ok and switch has no problem bcoz other PC is working fine Cable (cat 5 ) is also fine bcoz I didn’t crimp again just check in LAN tester and start working fine. Plz any one solve this matter. And after lan tester process pc is working fine and after 2 or 3 hour it again start same problem and again same process lan tester I have used

5 Answers  

---

Bridges work at what layer of the OSI model? A.) Data Link B.) Network C.) Physical D.) Application

2 Answers  

---

hi i am facing one problem.ptoblem is like that i am getting output error on mine router ethernet interfae here is the cisco#show interface e0 Ethernet0 is up, line protocol is up Hardware is QUICC Ethernet, address is 0030.802d.2a17 (bia 0030.802d.2a17) Internet address is 202.122.20.225/28 MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec) ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:00, output 00:00:00, output hang never Last clearing of "show interface" counters 05:55:07 Queueing strategy: fifo Output queue 0/40, 0 drops; input queue 0/75, 0 drops 5 minute input rate 10000 bits/sec, 11 packets/sec 5 minute output rate 29000 bits/sec, 11 packets/sec 1515202 packets input, 359100396 bytes, 1 no buffer Received 6 broadcasts, 0 runts, 0 giants, 1 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 0 input packets with dribble condition detected 1584394 packets output, 1623395338 bytes, 0 underruns 1820 output errors, 26732 collisions, 0 interface resets 0 babbles, 0 late collision, 9698 deferred 18 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out output cisco# what is the reason how to solve this please tell me i am using cisco asa 5520 behid mine internet router and no error on the asa inside interface

2 Answers  

---

Tell me how much internal and external ad of eigrp protocol?

0 Answers  

---

Which three are typical operational phases in a basic connection oriented network service? A. call setup B. data transfer C. load balancing D. call termination E. caller ID F. call prionflication G. data segmentation H. data and momma I. data link identification J. callering book

1 Answers  

---

What is the maximum hop count for IP RIP? A.) Infinity B.) 16 C.) 15 D.) 1

3 Answers   Cisco,

---

What is a back off on an 802.3 networks? A. It is latency in store and forward switching B. It is the time used for token passing from machine to machine C. It is the retransmission delay that is enforced when a collision occurs D. It is the result of two nodes transmitting at the same time. The frames from each transmitting device collide and are damaged

1 Answers  

---

What device has content-addressable memory (CAM) and what is stored in it? 1 A: Switch, learned IP addresses 2 B: Router, learned IP addresses 3 C: Switch, learned MAC addresses 4 D: Router, learned MAC addresses

4 Answers  

---