Answer / ranji2011

Hi,

Two different VTP domains cannot exchange VLAN database
information. In fact, splitting a switched network into more
VTP domains is one of the few ways how to make one part of
the network independent from another with respect to VTP. If
two switches are supposed to synchronize their VLAN
databases via VTP, they must be a part of the same VTP
domain. There is no workaround.

Answer / ranji2011

Hi,

If you are concerned about the communication, i wish to
inform you that It will definitely communicate. But if in
the case of exchange the "VLAN database information" as I
aforesaid, it will not.

Regards,

Ranji
Network engineer
netranjit@yahoo.co.in

Answer / guest

Two different VTP domains cannot exchange VLAN database
information. In fact, splitting a switched network into more
VTP domains is one of the few ways how to make one part of the
network independent from another with respect to VTP. If two
switches are supposed to synchronize their VLAN databases via
VTP, they must be a part of the same VTP domain.

Answer / nandlal chauhan

i think two VTP domain can communicate with the help of
inter vlan routing.

Answer / raje

using inter vlan routing it is possible to communicate two
switches in different network

Answer / veepee

BY creating a 2 different VTP domain we are only saperating
the VLAN traffic getting propagated to the other switches
in different VTP domain but the end nodes can communicate
with each other without any barear

Answer / pitabas panda

Yes both VTP domain can communicate,if you are configuring inter-valn in your layer 2 network.VTP is a layer 2 protocol,so if you configuring different vtp domain then vlan information can not synchronous with other VTP domain.

LAN stands for which of the following? A.) Local Area Network B.) Local Arena Network C.) Local Area News D.) Logical Area Network

4 Answers  

Which reserve port no http use?

1 Answers  

The "ipx delay number" command will allow an administrator to change the default settings. What are the default settings? A. For LAN interfaces, one tick; for WAN interfaces, six ticks B. For LAN interfaces, six ticks; for WAN interfaces, one tick C. For LAN interfaces, zero ticks; for WAN interfaces, five ticks D. For LAN interfaces, five ticks; for WAN interfaces, zero Ticks

1 Answers  

You have two Cisco routers setup back-to-back in a lab using DTE/DCE cables. To which router would you add the clockrate command? A.) The serial port on the DCE router B.) The Ethernet port on the DTE router C.) The Ethernet port on the DCE router D.) The serial port on the DTE router

2 Answers  

Which of the following describe SMTP? A.) Used for downloading files to the router. B.) Used for sending e-mail. C.) Uses TCP. D.) Uses UDP. E.) Uses port 25. F.) Used for managing IP devices.

1 Answers  

Identify the default encapsulation on serial interfaces? A.) ISDN B.) HDLC C.) SDLC D.) Frame Relay E.) PPP

2 Answers  

The Internet Control Message Protocol occurs at what layer of the seven layer model? A.) Physical B.) Transport C.) Session D.) Datalink E.) Presentation F.) Network

3 Answers  

Identify the keystroke used to terminate the setup mode? A.) Ctrl-K B.) Crtl-C C.) Ctrl-Z D.) Crtl-End

1 Answers   Cisco, HCL,

Which network mask should you place on a Class C address to accommodate a user requirement for five networks with a maximum of 17 hosts on each networks A. 255.255.255.192 B. 255.255.255.224 C. 255.255.255.240 D. 255.255.255.248

7 Answers  

Identify the components in the following command 'interface serial0/1/1' A.) Serial interface, port number 0, slot 1, port adapter 1 B.) Serial interface, slot 1, port number 1, port adapter 0 C.) Serial interface, slot 0, port adapter 1, port number 1

2 Answers  

What does the following series of commands accomplish? router igrp 71 network 10.0.0.0 router igrp 109 network 172.68.7.0 A. It isolates networks 10.0.0.0 and 172.68.7.0. B. It loads igrp for networks 109 and 71. C. It disables RIP. D. It disables all routing protocols.

1 Answers  

Why Clock rate command is not configured on ethernet interface of a router?

6 Answers