Interested to Buy Any Domain ? << Click Here >> for more details...
How we can find ASBR Router, we have no authentication to enter router?
- 3 Answers
- 7560 Views
- Logica CMG, Wipro, I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / rav
hi
without accessing router we not able to know router behavior
well ASBR always connects with BR and another side ISP end
other wise no other option to find
| Is This Answer Correct ? | 6 Yes | 0 No |
Answer / rohit
yes , we can find out the ASBR router by the topology...
the router doing the redistribution of another route into the ospf domain then that router should be ASBR router...
| Is This Answer Correct ? | 2 Yes | 0 No |
Answer / pinaki
HI,
WHEN WE CAN ACCESS ANY ROUTER IF THE ROUTER ONE 'AS' IS 0
AND OTHER 'AS' NUMBER ALSO PRESENT, THAT MEANS THE ROUTER IS
AUTONOMOUS SYSTEM BORDER ROUTER. THANKS
PINAKI DEY
KONNAGAR
| Is This Answer Correct ? | 1 Yes | 1 No |
When setting up a WAN network, everything outside of the Demarc is not owned by the customer. Which of the following are not owned by the customer? A.) The T1 line. B.) LAN C.) The Router D.) DTE E.) PC's F.) CO
What are the different types of cables that are used in routing?
hi... i am a beginner to CCNA... i find it hard understandin collision domain n broadcast domain.. please don tell me the definition.. i read the definitions many times... i need a more detailed explanation... like whn i read the definition it sounds simple... but i don understand whn they say it like a hub has one collision domain and one broadcast domain... and if collisions happen inside collision domain... i am confused... please help me... :(
What are the two primary operating modes for frame switching? A. Full Duplex B. Half-Duplex C. CSMA/CD D. Cut-through E. Fragmentation F. Store and Forward G. User mode H. Privileged mode
What is the difference between the communication and transmission?
How we can see mac address from dos prompt?
Identify the command to disable CDP on an interface? A.) Router(config-if)# no cdp enable B.) Router(config-if)# no cdp run C.) Router# no cdp enable D.) Router(config-if)# no cdp
how we can creat VPN..??? how it can be configured on cisco switches..??? can we creat VPN on different networks..??? why we need to create VPN..??? kindly write complete activity of commands to configure a VPN on switch..??? me specially looking towards Jatendra and Shahin
As the system administrator, you enter the following commands at the command prompt: ipx routing access-list 800 permit 2b 4d int e0 ipx network 4d ipx access-group 800 out int e1 ipx network 2b int e2 ipx network 3c What did these command accomplish? A. Traffic from network 4c destined for network 4d will be forwarded out Ethernet0. B. Traffic from network 3c destined for network 4d will be forwarded out Ethernet0. C. Traffic from network 2b destined for network 4d will be forwarded out Ethernet0. D. Traffic from network 4d destined for network 2d will be forwarded out Ethernet0.
Hi Friend. i have to let you know that now i have been selected for cisco india in bangalore. i am thanking to all of you guys that u have been posted such good question and the respective answer. from today i will be not able to visit this site on regular basic and hopeing that you will continue to post the question.the question you are posting is not very usefull to you but also usefull to another. i am again thanking to all of you and hope for best for your feature. Jitendera kumar sinha Network engineer-L2 cisco india Bangalore
Which of the following would not be displayed by the command ?sho cdp neighbor detail?? A.) The incoming/outgoing interface. B.) The hardware platform. C.) One address per protocol. D.) Amount of Flash Memory Available E.) The routers hostname. F.) The subnet mask, if IP is configured.
How many types of ends in wan?
CCNA 
