In the setup dialog, what do the square brackets indicate?

A. current or default spores

B. hard coded values that cannot be modified

C. values entered by the administrator but not saved

D. values that must be written to NVRAM before becoming enabled



In the setup dialog, what do the square brackets indicate? A. current or default spores B. har..

Answer / guest

Answer: A

Is This Answer Correct ?    3 Yes 0 No

Post New Answer

More CCNA Interview Questions

WHY DO WE USE the command interface Vlan 1 ip adress x.x.x.x sub mask what does it do .. what does it create.. i know when we create it we can remotely telnet inti a router=switch. but what is the diff bwt vlan and intface vlan. ... vlan 1 bieng a native vlan remains there eve if i dont gv switch an ip address .. lease suggest.

1 Answers   Wipro,


What are four ways that Fast Ethernet compares to 10BaseT Ethernet? (Choose four) A. Fast Ethernet uses the same Maximum Transmission Unit (MTU) B. Fast Ethernet is based on an extension to the IEEE 802.3 specification C. Fast Ethernet uses the same Media Access Control (MAC) mechanisms D. Fast Ethernet preserves the frame format that is used by 10BaseT Ethernet E. Fast Ethernet errors a speed increase one hundred times that of the 10BaseT Ethernet

1 Answers  


Which of the following is a characteristic of a switch, but not of a router? A.) Switches forward packets based on the IPX or IP address in the frame B.) Switches forward packets based on the IP address in the frame C.) Switches forward packets based on the MAC address in the frame D.) Switches forward packets based only on the IP address in the packet

1 Answers  


Which peer authentication method and which ipsec mode is used to connect to the branch locations? (Choose two)

0 Answers  


Which addresses are INCORRECTLY paired with their class? A. 128 to 191, Class B B. 192 to 223 Class B C. 128 to 191, Class C D. 192 to 223, Class C

3 Answers  






A router on one side of a PPP link uses the resonance RTR1 and the password COPP1-PWD. Which configuration line on RTR1 enables a connection between RTR1 and another router named RTR2? A. username, RTR2 password COPR1-PWD, B. username, RTR1 password COPR1-PWD, C. username, RTR2 password COPR2-PWD, D. username, RTR1 password COPR2-PWD,

1 Answers  


let there are three switch and there are 3 ree valn craed on each switch that is vlan 2 on first switch valn 3 on 2nd switch and vlan 4 is cretaed on switch 3 i have implemnted intervlan routin through ciso switchses. the router is conected through its fa0/1 port by one switch and and the two switch are trunked with each other now question is that we want to comuniacte betwwen vlan but does alse want that only vlan 2 is allow to access internet (ISP)which is conected through s0 interface of router.and no any vlan can access that internet.what should be solution.

1 Answers  


router

4 Answers   Infotech,


Identify the purpose of the Ping command? A.) Share routing information with a neighbor router B.) Transmit user data when buffers are full C.) Test connectivity at layer 3 D.) Test entire protocol stack

1 Answers  


Which configuration task must you complete if a remote Frame Relay router does NOT support Inverse APP? A.configure static maps B.define an IP address locally C.disable DHCP on the Frame Relay router D.configure a static route to the remote network

1 Answers  


What three occurrences will reset the holddown timer after a triggered update? A.) Infinity is finally defined as some max number B.) HD Timer expires C.) Another update is received indicating a better metric D.) The router receives a processing task proportional to the number of links in the internetwork E.) The router detects fault LSP's propagating through the internetwork F.) Another update is received indicating net status changed

1 Answers  


Explain how many tables are in ospf protocol?

0 Answers  


Categories