There is a process in Frame-Relay where LMI resolves an IP
address
from a DLCI number. What is this called?
A.) arp
B.) inverse arp
C.) rarp
D.) automap
E.) reverse arp
F.) arp
Answers were Sorted based on User's Feedback
Answer / guest
Answer: B
Inverse Arp maps the Local DLCI number to the remote IP address.
Inverse Arp is a function of LMI.
Is This Answer Correct ? | 2 Yes | 0 No |
Which two statements about IP RIP are true? (Choose two) A. It limits hop counts to 31 B. It is a link state routing protocol C. It uses autonomous system numbers D. It is capable of load sharing over multiple paths E. It uses bandwidth as the metric for path selection F. It broadcasts updates every 30 seconds by default
If you have configured IPX on a Serial interface, which command would display the IPX network and node address on the Serial 1 interface? A.) show interface B.) show ipx s1 C.) show interface s1 D.) show ipx int serial 1 E.) show ipx int brief
Identify 3 IP applications? A.) AURP B.) ARP C.) Telnet D.) SMTP E.) DNS F.) RARP
What is difference between standard and extended access-list
17 Answers College School Exams Tests, HCL, Wipro,
Hi Guys I am facing one problem while configuring PAP over Point to Point links. Configuration scenario is like this. ROUTER 1: (Hostname – R1) R1(config)#username R2 password CCNA2 R1(config)#interface serial 1/1 R1(config-if)ip address 10.0.0.1 255.0.0.0 R1(config-if)#lock rate 64000 R1(config-if)#encapsulation ppp R1(config-if)#ppp authentication pap R1(config-if)#ppp pap sent –username R1 password CCNA1 R1(config-if)#no shutdown ROUTER 2: (Hostname – R2) R2(config)#usename R1 password CCNA1 R2(config)#interface serial 1/1 R2(config-if)#ip address 10.0.0.2 255.0.0.0 R2(config-if)#encapsulation ppp R2(config-if)# ppp authentication pap R2(config-if)# ppp pap sent –username R2 password CCNA2 R2(config-if)#no shutdown Now problem is that, after configure the command “ppp authentication pap” the “Line protocol” status goes down on each router. But when I disable this command using “no ppp authentication pap”, the “Line Protocol” status goes up. What could be the problem, can anyone explain it plzzz….!!! Thanks in Advance…!! Shahin..
What is a backoff on an 802.3 networks A. It is latency in store and forward switching B. It is the time used for token passing from machine to machine C. It is the retransmission delay that is enforced when a collision occurs D. it is the result of two nodes transmitting at the same time. The frames from each transmitting device collide and are damaged.
What is passive topology in ccna?
Identify the hardware component that stores the backup configuration? A.) RAM B.) NVRAM C.) Flash D.) ROM
Which of the following encapsulation types can be used on leased-line connections? (Choose two) ❍ A. HDLC ❍ B. Frame Relay ❍ C. ISDN ❍ D. PPP
What is the virtual path?
Which three are typical operational phases in a basic connection oriented neloyord service? (Choose three) A. call setup B. data transfer C. load balancing D. call termination E. call priortization F. data segmentation G. data link identification
Which of the following is true? A. The default is to send debug output to the console screen. B. To view debug output from a telnet session, the "terminal monitor" command must be used C. If the "logging buffered" command is used, the debug output would be sent to RAM and can be viewed with the "show log" command D. If the "no console loggin" command were configured, output would besent to a telnet session E. All of the above F. None of the above G. A, B, and C. H. A, C, D, and E.