How many Devices does OSPF & EIGRP Support

Answers were Sorted based on User's Feedback



How many Devices does OSPF & EIGRP Support..

Answer / jitendera

theroticaly more the 250

but in partical i not gooing beyond 50 to 100 it can suport
but
perfomance is too low

Is This Answer Correct ?    8 Yes 3 No

How many Devices does OSPF & EIGRP Support..

Answer / don

ospf-unlimited
eigrp-200

Is This Answer Correct ?    2 Yes 1 No

How many Devices does OSPF & EIGRP Support..

Answer / vinay

theroticaly

ospf unlimited
eigrp 250

practical

ospf unlimited
eigrp 100

Is This Answer Correct ?    1 Yes 1 No

How many Devices does OSPF & EIGRP Support..

Answer / sahil0105

OSPF Unlimited
EIGRP 224.

Is This Answer Correct ?    0 Yes 0 No

How many Devices does OSPF & EIGRP Support..

Answer / biswajit

no countable because router not connected in one
area.connected all over so ospf & eigrp it protocol not a
device.

Is This Answer Correct ?    3 Yes 6 No

Post New Answer



More CCNA Interview Questions

Identify the command mode necessary to enter the standard ping command? A.) Router(config)# B.) Router> C.) Router(std-ping)# D.) Router(config-if)#

1 Answers  


Identify the 4 that are WAN technologies? A.) HDLC B.) FDDI C.) 802.5 D.) HSSI E.) SDLC F.) Frame Relay

2 Answers  


Choose three reasons why the networking industry uses a layered model: A.) It facilitates systematic troubleshooting B.) It allows changes in one layer to occur without changing other layers C.) It allows changes to occur in all layers when changing one protocol D.) It clarifies how to do it rather than what general function to be done E.) It clarifies what general function is to be done rather than how to do it

1 Answers  


What does the command show access-lists 101 list? A. all defended access lists B. all access lists within the router C. the contents of standard access list 101 D. the contents of defended access list 101

1 Answers  


What is the maximum value of administrative you can use?

0 Answers  






Which of the following will show an extended access list 150? A.) sh access-list B.) sh ip int C.) sh ip access-list 150 D.) sh access-list 150 extended

1 Answers  


How do you disable CDP on the entire Router? A.) Router#no cdp run B.) Rotuer(config-if)# no cdp enable C.) Router(config)# no cdp enable D.) Router(config)# no cdp run

1 Answers  


Using the access-list command, 'access-list 1 deny 2.2.2.2', what else must be done to stop host 2.2.2.2 from sending any traffic out of physical interface E0, while still allowing other traffic? A.) In global mode, Add a line - 'access-list 1 permit 0.0.0.0 255.255.255.255' B.) On interface E0, Add a line - 'access-group 1 in' C.) In global mode, Add a line - 'access-list 1 permit all' D.) On interface E0, Add a line - 'access-list 1 in' E.) On interface E0, Add a line - 'access-list 1 out' F.) On interface E0, Add a line - 'ip access-group 1'

1 Answers  


What is segmentation and fragmentation?

0 Answers  


Identify the command that displays ethernet0/1 interface status? A.) show interface ethernet0/1 B.) show interface ethernet e0/1 C.) show interface ethernet0.1 D.) show ethernet0/1

1 Answers  


What will transport layer do when data coming from session layer. They asked about intial operation(3 - way handshake)

1 Answers   HCL,


Identify the keystroke used to terminate the setup mode? A.) Ctrl-K B.) Crtl-C C.) Ctrl-Z D.) Crtl-End

2 Answers  






Categories