Which of the following will apply IPX sap access list 1010 for incoming traffic, assume you are at the interface configuration? A.) ipx input-sap-filter 1010 in B.) ipx input-sap-filter 1010 C.) ipx access-group 1010 in D.) ipx access-list 1010 in
2 3317What command can you type to view the connections after telneting into multiple routers simultaneously? A.) sh users B.) sh ports C.) sh host D.) sh sessions
1 3231Which of the following is a valid extended IP access-list? A.) router(config)# access-list 101 permit tcp host 172.16.30.0 any eq 21 log B.) router# access-list 101 permit tcp host 172.16.30.0 any eq 21 log C.) router(config)# access-list 101 permit any any 172.16.30.0 D.) router(config)# access-list 101 permit ip host 172.16.30.0 any eq 21 log
2 10480What is the command to manually enter a static route? A.) IP route network B.) IP route C.) IP route < destination network> D.) IP route
4 5277What 2 commands verify end to end communications? A.) Trace B.) debug ip session C.) Ping D.) Route
2 3316Your Ethernet interface currently has the IP address of 1.1.1.1/24. You would like it to have a second IP address of 2.2.2.2/24. Which command will do that? A.) ip address 1.1.1.1 2.2.2.2 255.255.255.0 B.) ip address 2.2.2.2 255.255.255.0 secondary C.) ip address 2.2.2.2 255.255.255.0 D.) This cannot be done, you can only have 1 IP address per physical interface. E.) ip address 2.2.2.2 /24
1 3195Which command listed below sets the banner message when someone connects to the router? A.) message # B.) banner # C.) login banner # D.) description # E.) login description # F.) banner motd #
2 4392What should be the first command to create an access-list that prevents all users on subnetwork 10.10.128.0, using subnet mask 255.255.192.0, from being able to telnet anywhere? A.) access-list 101 deny tcp 10.10.128.0 0.0.63.255 any eq telnet B.) access-list 101 deny tcp 10.10.128.0 255.255.0.0 any eq telnet C.) access-list 101 deny tcp 10.10.128.0 255.255.192.0 any eq telnet D.) access-list 101 deny tcp 10.10.128.0 0.0.192.255 any eq telnet E.) access-list 101 deny tcp 10.10.128.0 0.0.128.255 any eq telnet F.) access-list 101 deny tcp 10.10.128.0 0.0.127.255 any eq telnet
1 3702Identify the command to display the IP routing table? A.) show route B.) show ip route C.) show ip table route D.) show ipx route
1 4115Identify the command to display all the valid commands at the given mode? A.) Help all B.) Help C.) All commands D.) ?
2 4767Identify the keystroke used to terminate the setup mode? A.) Ctrl-K B.) Crtl-C C.) Ctrl-Z D.) Crtl-End
2 6690Identify the command to display the IP host table? A.) show ip hostnames B.) show ip names C.) show hosts D.) show ip hosts
1 5714Identify the command to display the configured IP routing protocols? A.) show protocols B.) show protocols all C.) show routing-protocols D.) show ip protocols
2 4253Identify the command to configure ALL the default VTY ports? A.) Router(config)# line vty 0 4 B.) Router# line vty 0 4 C.) Router(config)# line vty D.) Router(config)# line vty 0
2 10031
Tell me how many fillers we can put in one ip of ipv6?
Define ios?
Which multicast ip eigrp protocol use?
What are the advantages of lan switching?
What is difference between routing and routed protocols?
What is loop back ip in ipv6?
How much internal and external ad of eigrp protocol?
What is the point-to-point protocol in ccna?
What requirements should a VPN fulfill?
What is ping utility?
Can you describe the Authentication Header (AH) Protocol?
Explain protocol?
Suppose we are having two Switches i.e. Switch1 & Switch2 Port1 of Switch1 is Connected to Uplink and switch2 is also connected to switch1? So 1>Is there is any loop? 2>How we come to know that there is a loop created? 3>If we add Switch3 to switch2 then there is a possibility of loop Creation?
What is the difference between ‘bit rate’ and ‘baud rate’?
Explain isakmp ?