Regarding a full-mesh network and a partial-mesh network, what is the most accurate statement? A. Split Horizon will not work on a full-mesh network B. A full-mesh network is more expensive because more routers are used C. A partial-mesh network is less expensive because less virtual circuits are used D. Broadcasts are more plentiful on a partial-mesh network
1 4627SNMP agents are: A. Management devices B. NMS (Network Management Stations) C. network devices such as routers, switches, or hubs D. PDUs
1 7871What should be looked at first to determine if a customer should switch from a hub environment to a switched environment? A. Investigate the number of broadcasts B. Investigate the number of collisions C. Determine what routing loops are present D. Determine which switching type is being used by the hubs
1 2454What category or categories does Client/Server fit into the following Job Aid? Name of Protocol Type of Protocol # of Users # of Hosts or Servers Comments
1 2745Which condition does not create LAN media problems? A. Protocol doesn?t scale well B. Long wait for the token C. Excessive collisions D. Too many devices
1 2340Which of the following does not specify an application requirement that affects your network design? A. The number of users B. The peak hours that the applications are used C. The types of applications used D. Security risks
1 2471Match the following devices with the correct description. A. Switch 1. Operates at the physical layer and extends the cable as if it is a single cable. B. Router 2. Operates at the physical layer and connects all connections into one device or concentrator. C. Repeater 3. Operates at the network layer and can filter both hardware and network addresses. D. Hub 4. Works at the Data-Link layer and transmits a digital signal only to the specific port where the destination MAC address is located.
1 3060What happens when the hold-down timer expires? A. Routes are flushed from the routing table after the flush timer expires B. Routes are flushed from the routing table immediately C. Routes are never flushed D. A triggered update will reset the hold-down timer
1 6099Which of the following is not true in regards to route summarization? A. It increases the size of the routing table B. It increases the complexity of the network C. IP networks must be contiguous to be safely summarized D. Routing tables must have the capacity to support classless routing
1 3388What network design is becoming common when there is a central office with one or more remote locations? A. ISDN PRI at the central location and ISDN BRI at the remote locations. B. Using core routers at all sites C. Only using access routers D. Using a full mesh network
1 2434When doing an RFP (Request for Purchase) for a customer, at what step do you reiterate your solution and the customer requirements? A. Design Requirements B. Design Solution C. Summary D. Appendices
1 3581When are SNMP traps sent? A. When the SNMP manager wants to perform remote configuration on a networking device B. When an SNMP agent wants to inform the SNMP manager about a change of state on the networking device C. When the SNMP manager wants to access large chunks of data D. When the NMS wants to share trap information
2 3457
What is the igp (interior gateway protocol)?
Which command we give on privilege mode for coming back to user execution mode?
What is difference between static and dynamic routing?
What are the different types of network in ccna?
Explain protocol?
Mention what is bootp?
What is raid in ccna?
What is the mac address?
hi shain can u send me some detail about bgp so that i can enhance my knowledge over bgp and can you also teach me about the process of suppernating. now what i am thinking that this could be last visit on that site overhere.so please mail that short of thing on my gmail id i am requesting to all of the visitor that please send theire doubt or question to my new gmail id which is jitendera.ccnainterview@gmail.com.i will try to solve it if i am capable to do it Wishing all of you for great future Jitendera kaumar sinha
What is the default size of frame?
What is ‘round-trip time’?
What is the working of router?
Which protocol supenetting is enable by default?
What cable called v.35?
what is prefix list