Interested to Buy Any Domain ? << Click Here >> for more details...
As the system administrator, you type "ppp authentication chap pap secret". Which authentication method is used first in setting up a session? A. secret B. PAP C. CHAP D. PPP/SLIP
1 4717What are the three phases of PPP session establishment? A. Link establishment phase B. Authentication phase C. Network layer protocol phase D. Handshake phase E. Dial-in phase
2 12342What is the default IPX Ethernet encapsulation? A.) SNAP B.) Arpa C.) 802.2 D.) Novell-Ether E.) SAP
1 4375What must be true for two Routers running IGRP to communicate their routes? A.) Same autonomous system number B.) Connected using Ethernet only C.) Use composite metric D)Configured for PPP
3 7835The following is partial output from a routing table, identify the 2 numbers in the square brackets; '192.168.10.0 [100/1300] via 10.1.0.1, 00:00:23, Ethernet1' A.) 100 = metric, 1300 = administrative distance B.) 100 = administrative distance, 1300 = hop count C.) 100 = administrative distance, 1300 = metric D.) 100 = hop count, 1300 = metric
1 4448Identify 3 methods used to prevent routing loops? A.) Split horizon B.) Holddown timers C.) Poison reverse D.) SPF algorithm E.) LSP's
2 11507Which statement is true regarding full duplex? A.) Allows for transmission and receiving of data simultaneously B.) Only works in a multipoint configuration C.) Does not affect the bandwidth D.) Allows for transmission and receiving of data but not a the same time
2 10103Identify the switching method that receives the entire frame then dispatches it? A.) Cut-through B.) Receive and forward C.) Store and forward D.) Fast forward
1 4619Identify the purpose of ICMP? A.) Avoiding routing loops B.) Send error and control messages C.) Transporting routing updates D.) Collision detection
2 10210Which statement is true regarding the user exec and privileged exec mode? A.) The '?' only works in Privileged exec B.) They are identical C.) They both require the enable password D.) User exec is a subset of the privileged exec
1 10779Which OSI layer end to end communication, segmentation and re-assembly? A.) Network B.) Transport C.) Physical D.) Application E.) Data-Link F.) Presentation
3 12547What IP command would you use to test the entire IP stack? A.) Stack-test B.) Arp C.) Telnet D.) Ping E.) Trace
2 8800Identify the 2 hardware components used to manage and/or configure a router? A.) Auxiliary port B.) ROM port C.) Management port D.) Console port
3 6472What is the default bandwidth of a serial connection? A.) 1200 baud B.) 1.544 Mbps (T1) C.) 10 Mbps D.) 96Kpbs
2 13174
difference between layer 3 switch and router
What is osi reference model?
GUYS i was refraining the OLD post and i got a good Question and wana make sure that you guys Just did not vist it for answers if you are not Aware google it understand it and then answered it the question is -: Significance of IP helper-address Command on SW? Is it necessary to put this command? you donot wana to give answer please donot visit this question and increase the vistor name if you are thinking that answer is wrong mark it wrong and explain why you are marking it wrong
What is the difference between simple authentication and md5?
What is the logical link control?
What is the difference between rip and igrp?
Suppose a Switch interface went in error-dis mode what you will do for Troubleshooting List all Possibilities
What cable called v.35?
Which protocols are link states?
Which peer authentication method and which ipsec mode is used to connect to the branch locations?
What are the steps of data encapsulation?
Which feature should a routing protocol have to support vlsm?
What is the frame relay?
Given the configuration example: interface ethernet0 ipx network 4a ipx access-group 800 out interface ethernet1 ipx network 3d interface ethernet2 ipx network tc access-list 800 permit 3d 4a Which action result from implementing this configuration? a-Traffic from network 3d for network 4a will be forwarded out e0 b-IPX network 5c will not receive any traffic c-Traffic from network 3d, destined for network 4a, will be forwarded out e2 d-Traffic from network 3d for network 3d will be forwarded out e0
Tell me why we use filter option?
